Industrial 6t gas boiler Price Turkey

You must know the industrial 6t boiler price turkey energy problems (induced draft fan power consumption rate, steam consumption) draft fan causes problems 1.1 boiler flue dust and fouling, in particular air preheater fouling, resulting in increased resistance to smoke duct . 1.2 boiler flue, tail heating surface and dust leakage. 1.3 Leakage Rate large air preheater. 1.4 furnace excess air coefficient is too large. 1.5 unit load changes, run the adjustment is not timely, resulting in furnace pressure is too large. 1.6 unit load or low frequent starts and stops. 1.7 coal into the furnace worse, from the design value. 1.8 low efficiency filter. 1.9 draft fan blade badly worn, low operating efficiency. 1.10 fan outlet flue gas desulfurization big resistance. 1.11 soda boiler pipes for leaks. 2, 2.1 to 2.1.1 operational measures to solve the problem of the strict implementation of soot blowing system to prevent the heated area ash, blocking ash, flue gas system to reduce resistance. 2.1.2 holding the induced draft fan, the flue gas separator baffles and dampers in the fully open position. 2.1.3 The experiment showed combustion boiler, proper control of excess air in the furnace. 2.1.4 adjustment chamber negative pressure, air leakage reduction furnace and the flue. 2.2 routine maintenance and testing 2.2.1 induced draft fan performance test to determine the optimum operating point and efficient workspace. 2.2.2 boiler, air preheater, a flue, ESP and other system leakage inspection, process. 2.2.3 timely check processing chassis, shaft seal leakage. 2.3C / D repair, eliminating defects 2.3.1 down strict accordance with movement clearance adjusting fan. 2.3.2 induced draft fan blade defect action elimination hand vane opening adjustment. 2.3.3 Importers and induced draft fan baffle opening check. 2.3.4 duct tightness check process. 2.3.5 wave plate replacement air preheater, rinsed sector plate gap adjustment. 2.3.6 eliminate dust defects and improve collection efficiency. 2.3.7 clean flue gas desulfurization system, flue resistance is reduced. 2.3.8 eliminate soda boiler pipe leakage defects. 2.4A / B repair and transformation 2.4.1 Check and repair the fan blades, replace seriously damaged blades if necessary. 2.4.2 for energy saving fan efficiency below 75%. 2.4.3 The fan motor frequency transformation. 2.4.4 of the precipitator, if necessary, transform and improve collection efficiency.

Diqing in Yunnan Nonferrous Metals Co., Ltd. mainly engaged in Pulang copper mining, site selection, sales and other items. As we all know, in the copper smelting process, it consumes a lot of electricity and thermal power resources, which account for most of the hot water consumption. Combined with the actual demand Diqing company, to provide fast Boiler 1 stage electric heating hot water industrial 6t boiler price turkey of 2.1MW.

The transformation of low nitrogen industrial 6t boiler price turkey should be noted that what matters for retrofitting low nitrogen boiler should be noted that what? Of nitrogen oxide emissions is large, complex sources, environmental problems caused by acid deposition, fine particles, ozone, nitrogen oxides and analysis of contamination status must be further strengthened. If you do not take further measures to reduce emissions, with the United States and the United States to speed up economic development, population growth and urbanization, nitrogen oxide emissions will continue to grow in China in the future. Based on current trends, by 2030, emissions will reach 35.4x106 tonnes, will inevitably cause serious environmental impacts. Therefore, we must effectively enhance the emission control of nitrogen oxides. From this we can see that low nitrogen boiler is imperative! A check device to check for low NOX combustion gas before commissioning is in place, the gas pipeline flow is clean, whether the valve is open. There is a burner pipe leaks, reasonable pipeline installation. Discharging vent pipe valve from the foregoing, to ensure that no mixing of the air duct, and the exhaust pipe should be connected to the outdoor. Second, stable combustion and combustion of homeostasis Remember, combustion adjustment is the basis for all of the low nitrogen burner adjustment, as long as guaranteed under any changes in operating conditions of combustion stability and combustion of dynamic equilibrium, to burn steam temperature influence is even greater. Since the steam temperature is a sign flue gas heat value balance between the steam and heat absorption, this can be maintained as long as the dynamic balance, steam temperature can be kept stable. Third, the level of flame boiler boiler central flame center is also an important factor in high impact low-temperature steam. In the high temperature steam operation, the amount of coal combustor exhaust can be reduced, the amount of the lower stage burner of coal may be increased, and vice versa. Running low nitrogen burners, it should also be noted effect of different combinations of temperature steam mill. Steam at a low temperature exhaust composition regulating a large margin, the combination of the high temperature exhaust temperature adjusting stage so small margin overheat. It should be strengthened and soot blowing air distribution according to the situation.

Gas oil furnace and expansion tank should pay attention to what effect the high slot: the gas oil furnace, I believe we will not feel strange, but should also have a certain degree of knowledge and understanding, if the box has been concerned about the industrial 6t boiler price turkey site, and at the same time to carefully read the relevant article, and at the same time, to grasp their knowledge of words. So, based on this, then, we will continue this work, to promote a good learning process of the product, and so that everyone from a new harvest and inspiration. 1. Gas conducting oil conducting oil furnace exhaust port, which is typically what position the boiler on? HTF HTF furnace gas exhaust port, generally speaking, at the top of the boiler, i.e. high boiler shell. Furthermore, in this site, as well as the seat member, it is mainly used to install safety valve. Moreover, this drawing on the boiler, also will be marked out, as long as you can read drawings, you can, so can avoid making mistakes. 2. Gas expansion slot conducting oil furnace, which is in use, should pay attention to what issues? Gas expansion tank of oil furnace, the origin of their name, in part because of the boiler will heat transfer oil into the expansion slot, the expansion play a role. And this means that during erection, caution needs to be done is, it can not be damaged or broken. In addition, the oil level in the expansion tank, should be well controlled, so as to ensure the normal operation of the boiler.