Electric china heating water tube steam boiler manufacturers of the heating process due to elevated water temperature within electric steam boiler, heating and evaporation of the bubble surface of the metal wall temperature begins to rise at any time. There are heating and hot water boiler bath for two purposes. Hot water boiler by circulating hot water circulation pump hot water holding tank, the tank hot water heating cycle can be achieved bath object; hot water boiler by circulating hot water circulation pump heating conduit, through the heat sink (radiator) people can achieve heating requirements; hot water boiler and hot water circulating pump with heat exchanger can be achieved bathing and heating dual function. Steam boiler is an energy conversion device, the energy input to the boiler fuel chemical energy, electrical energy, thermal energy and other forms of high temperature flue gas, and after converting the boiler, the steam output having a certain outside thermal energy, high-temperature hot water or an organic carrier. Since the bubble greater wall thickness, in the electric boiler of the heating process, the thermal stress is a major problem, it is necessary for the thermal expansion of the bubble temperature and thermal stress study. At the same time, also considering the overall thermal expansion problems, especially an electrical heating surface tube steam boiler, since the thin wall thickness, length of problems in the process of heating the whole of the problems of thermal expansion, it should also be noted that the thermal stress. Prevent inadvertent failure caused. In the process of generating steam and processing the thermoelectric pressure steam boiler, when the temperature is higher than the outer wall temperature of the inner wall, the upper wall at a temperature above the wall temperature, the wall thickness and the temperature difference between the upper and lower walls of the bubble there is a temperature difference, i.e., bubble the inner wall temperature above the temperature of the outer wall, the wall temperature is higher than the wall temperature, the temperature difference between the thickness of the bubble exists in the thickness direction, the upper and lower walls of the larger temperature difference between the bubble, when the temperature is higher than the outer wall temperature of the inner wall, the wall temperature is higher than the wall temperature. In order to prevent excessive thermal stress, it is necessary to gradually increase the pressure of the boiler. In the process of electric spark and boost steam boiler, the steam parameters of the boiler components, water and conditions are changing. Therefore, in order to effectively prevent the occurrence of abnormal conditions and other hazards, it is necessary to arrange a variety of instruments to monitor closely the instruction of professional change. Within the normal allowable range, but also the reliability and safety of various instruments, valves and other components was evaluated by adjusting the process parameters pressure, temperature, water, etc., in order to fully guarantee the security of the electric steam boiler stable operation. The higher the electric steam boiler pressure, the higher the energy, the corresponding steam plant, pipes and valves can withstand the pressure will increase, which also makes the maintenance and protection requirements of the steam boiler is relatively high. In the production and transportation, and the ratio of heat loss will increase the share of the steam.

Meanwhile, at the annual meeting of the excellent performance of employees also distributed millet television and different incentives such as bonuses, is intended to encourage employees to continue their efforts to create more success in 2019. In the meeting, the president has placed us deep hopes in 2019 to focus the project, focus on value, cohesion output! Let the wind and waves, temper forward to the next five-year development strategy for the company's work starting point, in order to achieve the objectives as an important breakthrough, and jointly create a more brilliant 2019!

Fuel gas control step and the blowing process air volume of the total fuel gas china heating water tube steam boiler manufacturers steam boiler is achieved by adjusting a liquid coupling scoop blower. Organization fuel gas steam boiler combustion, is to make a, air pressure, air flow of secondary air with the good. Adjusting the amount of primary air should meet it carries the fuel into the furnace ignition of volatile oxygen required, and to maintain a certain speed, and without clogging the fuel discharge pipe of the jet having a certain rigidity. Primary air volume is too large and too small, the wind speed is too high and too low, should be avoided. In addition to adjusting the secondary air of combustion of the fuel should ensure that the oxygen demand, but must maintain a certain wind speed and primary air is mixed with the master time should have a strong stirring and mixing coke penetrate "the Gray" kinetic , which requires the case may be, each layer of the secondary air flow rate, in order to achieve stable combustion and flue gas excess oxygen appropriate destination. Fuel gas steam boiler, secondary air with what is better? Primary air volume air volume of the total share is called the primary air rate. A small air fraction, pulverized coal is heated to at least the heat required for the ignition point, fire faster, but the amount of primary air to satisfy the principle of combustion of volatiles. Secondary air mixed with the primary air time to the right. If it is mixed before ignition, means an increase in the amount of primary air, so that the ignition delay; hypoxia combustion secondary air if mixed will make late after ignition; if secondary air is mixed all at one position, since the secondary air temperature well below flame temperature, the flame temperature decreases, the combustion slows down, causing the fire. Therefore, the secondary air mixed with fuel should be based on the nature of the combustion zone as required timely sent, so that the combustion of oxygen, and will not reduce the flame temperature to ensure complete combustion and ignition stability. One or two wind speed with what is better? Fuel gas steam boiler once the wind speed is high, the fuel gas stream will catch fire in places far away from the burner, the ignition point postponed; once the wind speed is too low, it will cause a blocked ducts, and ignition point is too far forward, the burner will burn , but also easy to coke near the burner.

About the kind of china heating water tube steam boiler manufacturers fuel oil boiler steam through the next, there are many main purpose, main features, a brief Automatic fuel gas steam boiler. A: The main purposes: food processing, printing and dyeing, pharmaceutical production and provide steam to provide steam sterilization, medical institutions, enterprises and institutions to provide steam for the other, the hotel's heating Automatic fuel gas steam boiler, the heating can also provide domestic hot water tank by . Second: The main features: 1, with central back burning structure, a large volume of water and gas boiler space, adaptable load capacity. 2, the indoor micro-pressure flame automatic steam boiler fuel combustion, the flame is fully extended, enhanced heat transfer, thereby reducing convective heating area, reducing the cost of the boiler. Smoke flow resistance is small, low-power consumption operation, operating cost savings. 3, in addition to the conventional four level height control, an additional level detector 5, the detection bit will stop when the boiler water, alarm, to ensure safe operation of the boiler. 4, the front smoke box special heat insulation materials, high temperature, low thermal conductivity, good anti-radical quenching heat capacity, greatly extending the life center back burning boiler before the smoke box, the furnace insulation is multilayer glass wool , light weight, low heat loss. 5, automatic oil-fired boiler steam pressure is controlled by Danfoss and Danfoss pressure controller and pressure transmitters joint control, pressure controller is responsible for ultra-high pressure interlock protection, prohibits burner working and alarm; pressure transmitter responsible for combustion engine to work to achieve some or all of control, to achieve automatic control of the exact steam pressure and steam pressure in the pressure range provided by a touch screen, detecting a pressure up to 0.002 MPa, more accurate pressure control. Thus avoiding a pressure controller general requirements of the production and the high vapor pressure of low pressure gas boiler or the actual requirements of the production of high pressure and low pressure gas boiler can not meet the disadvantages of the production requirements. 6, flue gas condenser fast side (optional) by the national utility patent, requires efficient use of steel-aluminum sheet Chi spiral tube heat exchanger, heat transfer surface is sufficient, the small side of the flue gas resistance of the system to meet the general burner. With flue gas condenser heat boiler efficiency can be improved more than 8%, the fuel gas savings of nearly 10%. These are the simple on automatic steam boiler fuel introduction want to be useful.