power station gas steam normal pressure water tube boiler supplier

How to choose a steam power station steam normal pressure water tube boiler supplier heat exchanger? Steam boiler heat exchangers are generally divided into two categories, one is a direct contact heat exchanger, and the other is an indirect heat exchanger. Fuel gas boiler is not only fuel but also refers to the gas boiler. Previously no such dual-fuel boiler, burner because either fuel or gas, no dual fuel burners. With the rapid development of the world energy equipment, some European countries begin production and sales of fuel gas burner, dual fuel burner and boiler combination of organic birth of a new breed of boiler - fuel gas-fired boiler. Biomass boiler is a kind of boiler to biomass energy as a boiler fuel called biomass boilers, steam boilers into biomass, biomass hot water boiler, biomass stove, biomass thermal oil heaters, vertical raw biomass boilers, biomass boilers and other horizontal. They are used to recover flue gas heat, to achieve energy saving effect of the separation device. In general, conventional steam boiler can be increased by a simple transformation of energy-saving effects, such as increased waste heat recovery installation, which is energy-efficient steam boilers advantage. To promote energy saving is largely the cause of the country, to create more profits for the company, cost savings. Choose a good heat exchanger is one way to achieve energy efficiency goals. Direct contact heat exchanger is a steam boiler with heat recovery and a high ability to remove pollutants in flue gas, but acidic water quality, not easy to use in hot water heating boiler. The so-called indirect heat exchanger, thermal energy means that we recovered from the condensed-called flue gas. Today, more and more people choose to use the steam boiler, the proportion of the market is also increasing. Such steam boiler flue gas discharged contains a large amount of steam, by condensation and release large amounts of latent heat of vaporization. Coal-fired boiler efficiency is much higher than coal-fired boilers. This boiler has a good effect on the selection of the indirect heat exchanger.

In October 2016, my company and the China Dunhuang International Hotel signed a ZWNSL2.1-1.0 / W-Y.Q vacuum condensing gas hot water power station steam normal pressure water tube boiler supplier to provide heating and hot water for the hotel. The boiler implementing the response to the national policy of environmental protection requirements and local environmental protection departments on a series of low nitrogen emission standard boiler requirements, in terms of design, manufacture, installation and other sectors have strict checks to ensure that the boiler safe and stable operation.

Several problems into a coal-fired power station steam normal pressure water tube boiler supplier fuel gas boiler fired boilers changed several issues should be noted that the fuel gas boiler: fuel oil (l) high temperature corrosion of the fuel used in the boiler, containing an organic salt of a metal element as sodium, vanadium class, after combustion of the low melting point eutectic oxide crystals, generally of about 600 ℃, or even lower. These oxides sublimation at a high temperature furnace, then condensed in a lower relative temperature of the heated surface to form a high temperature corrosive fouling. Is characterized by high temperature corrosion: the metal began to appear at temperatures in excess of 580-620 deg.] C, the higher the temperature, the faster the etching. High temperature corrosion measures to prevent: l) the use of additives. Mainly magnesium, calcium oxide, hydroxide or dolomite (CaC03, MgCO3) and the like, these additives can generate a high melting point compound with the component acting in a high temperature fouling, the fouling becomes loose and shape, so as to avoid or mitigate high temperature corrosion. 2) use high temperature materials with good corrosion resistance, high temperature corrosion resistant chromium steel is better than the nickel-chromium steel. 3) coated with a protective film. Susceptible to corrosion in high temperature heating surface ceramic surface coating, a silicon carbide or silicon nitride special coatings, the heated surface may be aluminized other treatment to improve its high temperature resistance. 3) coated with a protective film. Susceptible to corrosion in high temperature heating surface and other surface-coated ceramics, silicon carbide, silicon nitride, or special coatings, the heated surface may be aluminized other treatment to improve its high temperature performance rot cloud. (2) low temperature corrosion in fuel sulfur generated during the combustion S02, since the fouling atomic oxygen present in the furnace and the convection heating surface and catalytic oxide film, SO2 is further oxidized to S03. S03 and H2S04 vapor in flue gas generated in conjunction with, the dew point of the flue gas containing the sulfuric acid vapor is greatly increased, when heated wall temperature below the dew point of sulfuric acid vapor will condense on the walls, and corrosion of the metal wall. Usually low temperature corrosion It occurs at the end of the air preheater of the boiler. Thus when burning high sulfur fuel, care must be taken to prevent low temperature corrosion. Prevent low temperature corrosion measures are: 1) low oxygen combustion. When the excess air at the outlet of the furnace lag coefficient down to 1.10 or less, for sulfur of the fuel oil used, the dew point of the flue gas will be significantly decreased, so as to avoid or mitigate low temperature corrosion. 2) use of additives. Sprayed into the furnace or flue additive in the curb generation of SO3 and to reduce the flue gas dew point temperature. Common additives solid (dolomite, limestone, magnesium oxide, and some special compound), the liquid (aqueous magnesium chloride solution, some oil soluble magnesium, calcium, zinc naphthenate compound) and a gas (ammonia gas, ammonia, three different ring) three categories. 3) raising the thermal wall temperature, so that it is higher than the dew point temperature of flue gas. Commonly used methods are: hot air recirculation inlet temperature of the air preheater increase; the installation of the heater core, air is heated by steam, a low temperature air preheater horizontal structure, the level of a horizontal pipe line is arranged an air preheater , the air flow in the pipe, the pipe between the smoke flow, erosion due to the lateral wall of the flue gas, the flue gas side heat transfer coefficient is increased to increase the wall temperature, more generally vertical wall temperature of the air preheater increase 20 ~ 25 ℃. 4) corrosion-resistant materials or corrosion resistant coating materials include glass, ceramics and the like; an anti-corrosion coating and had tried to enamel-coated surfaces like special steel anticorrosion paint. 5) timely sootblowing operation, and therefore should be a reasonable arrangement sootblowers. Fire and explosion of fuel failure (3) heating surface of the tail or incomplete combustion of atomized droplets gather in the tail of the heating surface, when it reaches ignition or explosion conditions, i.e., ignition and explosion may occur. The tail heating surface fouling aggravated by the possibility of aggregation of the oil droplets. Therefore, when coal-fired boilers into oil-fired boiler, burner should be correct and rational selection and delivery, and strictly develop from the induced draft fan. Rules and procedures for shutdown and normal operation to ensure good fuel atomization, with the wind reasonable. At each of the heating surface is arranged to be reasonable sootblowers. (4) determining the dew point temperature of flue gas is determined dew-point temperature of the flue gas has practical significance for the design and operation of flue gas dew point temperature factors influence mainly sulfur fuel ink, excess air coefficient, water vapor in the flue the amount of sulfur / cement ratio and combustion.

To introduce steam power station steam normal pressure water tube boiler supplier pressure gauge and hydraulic press accumulator using steam boiler pressure gauge should pay attention to: 1, rated steam pressure is less than 2.45MPa steam boiler, the accuracy of pressure gauge must not be 2. 5; Rated steam pressure large or equal to 2.45MPa boiler, pressure must not be less than 1. 5 class. The diameter of the dial of the pressure gauge shall not be less than 100 mm to ensure that the operator can see clearly the surface pressure indicator value. 2. A red line should be drawn on the pressure dial of the steam boiler pressure gauge, indicating the maximum allowable working pressure. Steam boiler pressure gauges should be installed in a place that is easy to observe and wash. 4. Steam boiler pressure gauges should be checked at least once every six months, and should be sealed with lead after calibration. 5. Steam boiler pressure gauges should not have leakage of water and steam leakage in the connecting tubes of the pressure gauges of steam boilers. (4) the steam boiler pressure gauges should be checked at least once every six months and sealed with lead. 5. Otherwise, the pressure indicator value will be reduced. 6. The measurement range of the steam boiler pressure gauge should be adapted to the working pressure of the measured components, usually 1.5 times of the working pressure, preferably 2 times of the working pressure. Steam boiler does not have pressure gauge, the pressure gauge is damaged or the installation of pressure gauge does not meet the requirements, steam boiler pressure gauge should be stopped when one of the following conditions: 1, broken surface glass or dial calibration mold There is no clear paste; 2, no lead seal, lead seal damage or beyond the calibration period; 3, without pressure, the pressure gauge of the finite pin can not be restored to the limit pin, the infinite position of the gauge pointer deviated from zero data beyond the allowable pressure clothing; 4, gas leakage or pointer jump in the meter; 5, other defects that affect the accuracy of the gauge. Purpose of the accumulator: the accumulator is used in the hydraulic system of intermittent machinery, which stores the oil output of the hydraulic pump during intermittent or low-speed movement of the actuator, and when the rapid movement of the actuator requires a large flow rate, As an auxiliary energy source, together with the hydraulic pump, the oil pump is supplied to the system, thus the oil pump and the hydraulic pump are realized. The miniaturization of the whole hydraulic device absorbs the quick opening and closing of the impact hydraulic reversing valve and the sudden change of the load. The system will produce shock pressure, the darling will lead to vibration and noise, and even damage the machine. The accumulator can mitigate the impact pressure absorption pulsation of these fluids absorb and reduce the flow pulsation and pressure pulsation of various hydraulic pumps thus reducing the system noise and vibration. The damped accumulator acts as a gas spring and can be used to absorb the vibration between the fuselage and wheels of walking machinery such as vehicles. The balanced accumulator absorbs the gravitational potential energy of the vertical actuator (hydraulic cylinder) and its load as it falls. When the vertical actuator rises, the accumulator releases the original absorbed energy and supplies oil to the hydraulic cylinder together with the pump, thus realizing the balance and energy saving.