the capacity is 21tons oil fired hot water boiler shipped to argentina

What safety matters should be noticed in the operation of industrial boilers?

Industrial boiler is a kind of equipment which must be used by many manufacturing enterprises. It can provide sufficient thermal energy for the production of enterprises so as to ensure that the production can be carried out in an orderly manner. However, because the industrial boiler is dangerous when it is used, the workers who operate it must pay attention to the following items in their daily work in order to better prevent the occurrence of safety accidents. So what safety matters should be noticed in the operation of industrial boilers?

1. Industrial boilers should check the inlet and outlet valves of their gas meters and the main valves in front of the furnace before using them, and close them when the pipes are replaced. When opening the furnace door, we should pay attention to check the situation in the furnace, especially pay attention to the phenomenon of gas leakage, if the leakage is found, it cannot be ignited, but it should be checked and repaired in time to ensure the safety before ignition.

2, pay attention to check the flue of industrial boiler, can't have water or not and keep the flue open all the time. At the same time, no combustible and explosive products such as diesel oil, firecrackers and so on should be placed around the boiler, and safe passageways of sufficient area should be set aside.

3. Start the blower before igniting the industrial boiler and open the air valve on each burner. When igniting, we must pay attention to fire and so on. We must not put the cart before the horse in order to prevent explosion. Also note that the burner should be ignited and adjusted in sequence from top to bottom and from inside to outside.

4. When using industrial boilers, if the blower stops abruptly due to power outages and other reasons, all gas and air valves on the burner should be closed immediately and the furnace doors should be opened if necessary to prevent accidents.

5, the operating room should be equipped with a gas alarm, if found gas leakage of the county should close the indoor gas valve, and then find out the leak point and timely repair, in the course of its attention must not use open fire to detect leakage.

Hot water boiler belongs to special equipment, and is also a kind of high temperature and high pressure thermal energy equipment. It is inevitable that some faults will occur in the process of operation, which are normal, but it is very likely that the explosion of the capacity is 21tons fired hot water boiler shipped to argentina will occur if it is not properly dealt with. Therefore, for equipment safety and personal safety, we must understand some prevention hot water boiler explosion common sense. In the design of hot water boiler, thermal calculation and strength calculation should be carried out strictly according to the requirement, the structure layout should be reasonable, and the material selection should be qualified. In order to ensure the boiler quality conforms to the drawing, the boiler should be constructed according to the drawing. The degree of delimitation. Boiler safety accessories should be complete, agile and reliable, and on-time maintenance, frequent inspection, failure of accessories should be replaced in a timely manner. Repair and repair the boiler inside and outside the boiler according to the schedule, repair and reform the existing problems in time to ensure the quality of inspection. 2. Fuel oil and gas-fired hot water boiler explosion accident in furnace to prevent explosion of hot water boiler should be carefully checked before the point of the hot water boiler, whether the oil path is tight (leakage), the pressure is normal or not, and the newly installed and modified oil and gas pipelines must be blown clean. Check whether the blower has been ventilated for 5 minutes before ignition, and analyze the reasons after ignition failure, and then follow the ignition procedure to penetrate the air. Ignite. For boilers that have not been certified for boiler use and annual inspection, the grater has the right to refuse to light the furnace. The enterprise should lay down the experienced stoves who have rich experience in the operation of the furnace. The staff of the furnace should step up the tour inspection, deal with the problems in time, prevent the flameout, and stop the fuel as soon as it is found out. The boiler shall be equipped with automatic protection devices, including automatic ignition, flameout protection, automatic combustion regulation and necessary interlocking alarm protection devices.

Ovens and boilers boiler inspection methods oven to cook and cook blast furnace blast furnace inspection can be found as soon as possible the existing boiler problems and avoid boiler safety accidents in use, today we are speaking about the oven and cook for blast furnace boiler the inspection methods: 1, chain grate cold test run more than 48 hours. 2, coal gate installation is completed, the shutter plate on the coal should be closely good coverage, and other impurities to prevent leakage into the coal, coal stuck up and down the shutter, the shutter connected to water cooled coal, firing the door open and flexible. 3, boiler and subsidiary equipment Ge all assembled and pressure test qualified. 4, the end of the furnace wall masonry and insulation, and check whether the debris inside the flue cleaned. 5, thermal instrumentation boiler should check eligibility, and check the reliability of the boiler feed water, as well as water to the boiler to full level. 6, the required auxiliary oven test run is completed, such as pumps, fans, etc., have confirmed that each part of the work safety conditions to start, you can start the oven. 7, the furnace wall should be installed measurement points or sampling points. 8, all moving parts and should be required to add oil cup oil. Learn how to do the oven and cook blast furnace boiler inspections, I believe you must have learned a lot of knowledge of it, I hope this can help you use the more secure the boiler.

July 26, 2016, Beijing, China Everbright Paper Co., Ltd. and the company signed a "split 6 tons of steam condensing gas steam boiler contract" by the company responsible for the WNS6-1.25-YQ split condensing gas boiler steam to all production, installation and commissioning work. The product is the use of condensing technology, effective emission of harmful substances SOx, NOx, COx, is industrial boilers efficient and environmentally friendly solutions.