palm oil industry using what kind of boiler

Before the opening, Xiao Bian would like to ask you, for the "palm industry using what kind of boiler" the vocabulary, what concept? Heavy shell? Dark boiler room? Or the dusty it? In the fast boiler, all this will be broken. Into the fast side, the first thing is 120,000 square meters of factory area, 6,000 square meters of clean boiler test center, you will inevitably get lost. But now do not worry, we launched a corporate panoramic VR, sweeping away mobile phones, travel all know.

Fluidised beds have been used in the chemical industry. The first coal combustion applications, however, were not developed until many years later even though the fired patent on coal fired fluidised bed palm industry using what kind of boiler was applied two decades earlier. The energy crisis increased the interest of using coal as an alternative to oil and fluidised bed combustion offered a way to burn coal in environmentally more friendly way than conventional pulverised coal combustion. Later, fluidised beds have also been successfully applied to combustion of alternative fuels such as biomass and materials.

What are the three common palm industry using what kind of boiler combustion? Urban coal-fired boiler has been difficult to solve, because especially small coal-fired boilers type cluttered and more widespread particularly difficult to handle. On the one hand burning low power, on the other hand is more a waste of resources. Under the requirements of environmental protection requirements, many cities in the relevant part of the requirements necessary gas (oil) boiler retrofit or replacement of 10t / h coal-fired boilers. The transformation of the former needs to focus attention to the following questions: whether the site is useful region of central heating boiler heating of small alternative program. The useful life and corroded boiler, if the boiler by Zhengzhou fast boiler or other professional testing organization to determine the useful life of less than five years, the transformation of value is not high. Determine whether the laying of gas pipeline convenience, liquefied petroleum gas or other fuel supply and transportation issues. Comparing the cost of renovation and equipment manufacturers advantages and disadvantages, in determining the needs of the transformation plan in compliance with these principles. Selection of fuel. Under the premise of fuel sources have, the most economical natural gas pipelines, liquefied petroleum gas, followed by a final light diesel oil. Also, consider the surrounding environment from fire and explosion safety. In general, the system and the soda boiler pressure parts and preferably not modified to adhere to the original power, are demand, under conditions not substantially change the pressure member, than the original power increased by 10% to 20%. Boiler pressure parts for major changes in the program desirable. The transformation process is necessary to ensure the safety of boiler pressure parts of (mostly small commercial general pressure boilers), followed by incineration system to ensure the safety factor, the decline in the risk of explosion, fire accidents. Recognize the transformation of the planning process, in a timely manner, the environmental protection, the gas company, fire department, urban construction and timely communication with the boiler section to monitor and ensure the transformation plan can proceed smoothly. When the boiler is burning way during boiler selection will take into account an element, the following three common boiler burning approach advantages and disadvantages brief analysis cf: 1 Decentralized incineration strengths: this way is not burning premixed, but the gas nozzle mouth dispersed with each other, and then burning it. Incineration relatively simple way, as more stable as compared to the flame. Disadvantages: Due to a longer flame, it is prone to the phenomenon of incomplete burning, more carbon monoxide and nitrogen oxides will occur, it is not conducive to the use of full-fired boilers, to improve the thermal power of the boiler, and the boiler emissions standards are difficult to reach. 2. premix approaches incineration advantages: premixing air and gas, a multi-way heat radiator, to improve the strength of heat transfer. Strengths of this approach is that the burning of the burning flame is more clear, and the higher heating power. Disadvantages: incineration requires precise ratio premix burning rate is fast, uniform burning radiant heat transfer full power high flame temperature below 1200 deg.] C, all NOx completely burned and the occurrence of low flue gas temperature, condenses, good heat recovery and high power. 3. No flame burning incineration space before incineration approach uniform mixing with the gas in the gas boiler. When using this approach, in the process of incineration gas in the oxygen demand is not made in the ambient air demand, only needs to achieve instant complete incineration air mixture reaches the incineration zone. Approach in the selection of incineration, incineration demand for the advantages and disadvantages of different approaches, carried out mutatis mutandis selection, a good way is also advantageous burning boiler to reach plenty of incineration, thermal power increase, decrease the role of emissions, and therefore, it is important to choose carefully.

Oil and gas palm industry using what kind of boilers are a kind of costly equipment. When customers choose to buy boilers, they will always compare the benefits that different boilers can produce. Therefore, customers are very concerned about the price of the boiler. When communicating with our service personnel, customers always want to know the latest information about oil and gas boilers price.