Agent Price 4t gas boiler Commercial Cambodia

In the agent price 4t boiler commercial cambodia market, oil and gas boilers, coal-fired boilers, and biomass boilers occupy almost the entire market. Among them, many countries and regions have demanded the use of clean boilers because of their emphasis on environmental protection, which has also promoted the development of environmentally friendly oil and gas boiler manufacturers.

Shandong Zhaoyuan Mining Group Co., Ltd. is a large state-owned local asset management companies, gold mining dressing and smelting for leading industries, operates in the area of ​​tourism, services, precious metals, real estate, eco-agriculture, with total assets of 10.2 billion yuan, Shanghai gold Exchange is an international provider of standard gold bullion. July 2017, Shandong Mining Group and fast agent price 4t boiler commercial cambodia steam signed a 0.5-ton electric heating steam boiler which mainly produce steam for metallurgical mineral processing and other manufacturing processes, energy defeating small, strong ability to supply steam .

How to set the height of the agent price 4t boiler commercial cambodia chimney

The coal fired boiler can be divided into two kinds:vertical boiler and horizontal boiler. And the horizontal boiler is very economic because of its long flue gas flow, slow smoke discharge, high heating efficiency. So it is widely sued in the market. After buying a boiler, it is necessary for them to build a boiler room,in the installation the height of the chimney also need to pay attention. According to the ZG engineer, the chimney height should be accordance with the lowest height of GB13271-2001 stipulation. Only one chimney is allowed in a boiler room. The specific requirements was listed below:

1.When the boiler’s output capacity is more than 1t/h or 0.7MW, a permanent thief hatch and relevant facilities should be setted in compliance with the stipulations of measuring method for smoke and dust of boiler emission, and The determination of particulates and sampling methods of gaseous pollutants emitted from exhaust gas of stationary source.

2. The exit diameter of the chimney should be not lower than the largest load. The smoke flow should not be too fast. when the load of the coal fired boiler is at its lowest level, the velocity of the chimney exit should not lower than 2.5~3m/s.

3. If the chimney heat does not reach the height of the above stipulations, the maximum discharge concentration of the dust,sulfur dioxide, nitric dioxide should be carried out at 50% of the corresponding area and time emissions standard .

Burner fuel gas selected selection principles which fuel gas agent price 4t boiler commercial cambodia burners should be based on structural features and performance requirements of the boiler body, in conjunction with user conditions, making correct comparison, several general principles according to the following options: 1) according to user selection of used fuel type, liquid fuel kerosene, diesel oil, heavy oil, residual oil and waste oil, fuel gas city gas, natural gas, liquefied petroleum gas and biogas, fuel should have the necessary analysis of data used: ① kerosene, diesel should have heat and density. ② heavy oil, residual oil and the viscosity should, heat, moisture, flash point, mechanical impurities, ash, freezing point, density and the oil temperature. ③ should calorific gas, gas pressure and density. 2) to select the type burner nozzle atomization method or the gas burner and the furnace structure according to the performance of the boiler. 3) the burner output should match the rated output of the boiler, choose a good shape of the flame, such as length and diameter so as to adapt the furnace structure. The required combustion air is supplied from the root flare fuel gas and air or oil mist uniformly mixed rapidly, to ensure complete combustion. The rated output of the boiler and boiler efficiency is determined, the fuel consumption is calculated, and then selected according to power a single burner arranged to determine the number of burners. Increase the number of burners, in favor of the atomization quality assurance wind oil mix, but too many, and not easy to operation and maintenance, will give burner arrangement difficult. 4) adjusting the burner to a large extent, be able to adapt to changes in boiler load, to ensure complete stable combustion under different conditions. 5) fuel atomization less energy consumption, adjusting the wind resistance of the device to be small. 6) Effects of noise and smoke emission must comply with environmental standards, mainly emissions S02, CO and NOx must be lower than the predetermined country, should use low NOx burners and low noise. There are integral and split two 7) a burner assembly embodiment. I.e. monolithic burner body, the burner and a combustion air blower system (including an oil pump, a solenoid valve, a servo motor or the like) into one; split i.e. burner body (comprising a combustion head, oil or gas systems), fans and combustion burner control system (including the control box, fan thermal relay, AC contactor, etc.) are each independent three-part system, according to the specific requirements of the boiler and user choice. Simple 8) should be used in construction, reliable operation, easy to adjust and control the repair, easy to implement automatic control of the combustion process in the burner. 9) to deal with the burner brand, performance, price, and service life of comprehensive comparison. 10) In addition to the burner air pressure to overcome the resistance of the boiler body considered, but also to overcome the resistance and flue gas economizer system.