hot water oil boiler industry

Gas Steam Boiler non-normal stall, a phenomenon and treatment, flame reasons: 1, the operation of the auxiliary power supply or trip interruption. 2, boiler combustion instability. 3, the load is too low, so that the load sharply mill automatic ignition energy loss or failure of combustion. 4, mutant coal, coal volatile or low calorific value. 5, the automatic combustion flame detector failure or failure caused by tripping mill. 6, or blast furnace wall tubes serious improper boiler soot-blowing operation, a large amount of water vapor into the combustion chamber. 7, coal pulverizing system, fuel system failure, resulting in a significant amount of fuel reduction or interruption. Or with a large amount of water in the fuel oil gun blocked too many impurities, low pressure steam or atomized. Second, the phenomenon: 1, a significant increase in furnace pressure, furnace flame monitoring flameless CRT display. See the fire no fire hole, BTG warning window MFT warning lights. 2, the unit load decrease, the steam flow drops rapidly, each segment working medium temperature, the vapor pressure decreases, the value of oxygen surge. Third, the method of treatment: 1, if the MFT tripping protection, should an emergency shutdown processing, stop the supply of fuel. 2, identify the cause flameout, and try to eliminate, to conduct a comprehensive inspection of the boiler, after confirming the device properly, can restart.

Boiler cleaning the necessity and significance of the boiler after a long run, the inevitable emergence of scale, corrosion problems, these problems are due to the generation of scale, so that the heat transfer deterioration, resulting in reduced efficacy boiler. It is difficult to achieve nominal evaporation; and since the heat transfer is deteriorated, such that the metal overheating, under pressure boiler, furnace tube bulge occurs even explode; poor thermal conductivity, so that the fuel consumption is increased, increased operating costs, boiler shortened life expectancy. Therefore, the boiler scale, should take the necessary cleaning methods. Of the boiler system operated at optimized state, it must be specialized chemicals treatment of boiler system water system: to remove scale, rust and anti-corrosion treatment: 1 chemical cleaning: adding a chemical cleaning agent to rust in the system , dirt, cleaning oil dispersion is discharged, reduced to clean metal surfaces; 2, routine maintenance: boiler scale inhibitor is added, to avoid rusting of metal, to prevent the crystalline precipitate calcium and magnesium ions. Boiler cleaning in two parts, part of convection boiler tubes, superheater tubes, air heaters, waterwall tubes scale, rust cleaning, i.e. water boiler water treatment, we used the final Li Jing Ling descaling operation, neutral cleaning technology cleaning operation, relatively low cost; cleaning of the part of the outer tube, i.e. the cleaning of the boiler furnace, we used high-pressure water jet cleaning technology, it is possible to achieve good results. 1, the cleaning operation may be neutral at neutral or weak alkalinity (pH 7-12) conditions, the water does not change the operation of the boiler a predetermined state index, do not stop cleaning, cleaning can reduce the loss caused by the stop, this is a the only signs of cleaning. 2, security theory and practice of running the boiler have proven non-erosive, washed acid-free cleaning under neutral conditions, the corrosion rate is less than the water washing of the corrosion rate of the metal, no corrosion damage to the metal. 3, non-toxic and pollution-free operation of the Spirit is a green cleaning products, boiler blowdown COD after its cleaning. BOD. The pH full compliance with national standards. 4, easy to use drugs added to the water supply can be, without a separate professionals, post operator can operate, it can be widely used. 5, a significant saving, the cleaning process in which water is the normal production water, unlike dispensing additional consumption pickling, passivation, and a large number of repeated washing of freshwater resources consumed. High pressure water jet cleaning technology uses water as the medium, so that the water system by special equipment to produce multi-beam, multi-angle, high-pressure water jets of different intensity. Internal cleaning object fouling, plugging, or be completely cut surface adhesion, crushed, pressed and washed in order to achieve complete cleaning. Whatever the fouling deposits, high pressure water jet cleaning device for cleaning, can be completely removed, which considerably metal color. It does not require chemicals, or corrosive flux, safety, and environmental protection. Boiler air preheater, waterwall, superheater, economizer heating surface and the like due to clogging of the exhaust gas temperature, boiler efficiency is lowered, increasing the wind electrical energy consumption; the fan will cause severe blockage afford pulling negative pressure oxygen furnace not enough, boiler forced outage. Using high pressure water jet technology, the cleaning effect is obvious. Equipment from high pressure water pump, water hoses, high pressure gun, special nozzle and other components. Cleaning process: water pressure via a high pressure pump to the 50 ~ 100Mpa, via line transferred to the system actuators work surface, forming a bundle of fine high-pressure water emitted from the nozzle with a high pressure water jet but powerful strike capability, which exit velocity up to 380m / s, the heating surface fouling rinse. The high pressure cleaning technology to clean, easy to adjust, cleaning equipment to be non-corrosive, non-polluting the environment, the effect is obvious characteristics, is an effective and a good way to save money and effort, especially suitable for solving air preheater clogging, severe coking furnace heating surface slagging problems. Generally reduce exhaust gas temperature of 4 to 12 degrees, the main improved reheat steam temperature of 0.5 to 5 degrees, to reduce electrical energy consumption for the wind, and early detection of creeping inflation, under scale corrosion risks, the unit safe and economic operation of very help.

Fast boiler based on the local, to the world. In 2013, Alliance Group and Indian steel companies entered into a collaboration to deliver four single 26.7 tons of steam shell type boilers, famous at home and abroad.

Gas steam thermal cracking reaction furnace gas steam oven should be carefully introduced reflect in the use, to guard against water, acid, alkali and leakage into the low boilers using the system, the system should be installed filters installed to prevent debris into various types, to ensure the purity of the oil . Gas and steam is easily oxidized during heating, the acid value of the oil is increased at high temperatures and a large change rate. Steam oven gas kinematic viscosity gradually increases, which is due to the thermal cracking gas vapor component at high temperature, thermal polycondensation reaction. Thermal cracking reaction resulting in generation of small molecule compounds, to reduce its viscosity; oxidation temperature when the inner conduit thermally cleavage occurs at 300 ~ 400 ℃, coke formation in the pipe, the inner wall of the device, leading to heat accumulation pipe affect the heat transfer efficiency, sludge poor flowability, transfer oil accelerated aging failure, but also to the furnace, pipes local overheating, impairing the mechanical strength of the threat to personal safety.