42 MW Liquefied petroleum gas boiler in Indonesia

Gas 42 mw liquefied petroleum boiler in indonesia safe handling as the country increasingly stringent emission standards for air pollution, the country has already started work boilers from coal to gas, out of heavily polluting coal-fired boilers, gas boilers using clean fuels. In this regard, Kono Tips boiler, gas boiler process, the need to pay attention to some safety issues: 1. burner to keep the working environment clean and dry, burner cleaning and maintenance once per shift to the control circuit must not get wet, affected by high temperature. 2. Check the electrical installations, mainly: whether the damaged wire, jacket damage, without loosening the screws, the contact is good, the motor is running any abnormal sound. 3. During normal operation, the burner portion close to thermodynamic device (such as a flange connection part) will be very hot, to avoid burns. Do not place near flammable materials, so as not to cause a fire. 4. combustor during startup, if the burner is locked repeated alarm reasons should be identified, and then identify failures and excluded press the reset button (pressing the reset button must not exceed 10 seconds), continue to start. 5. After the total gas pipeline experienced a temporary power failure solenoid valve (steel tile shed) to stop gas supply will automatically shut down until the first call burner electric alarm device to send, then a small hammer solenoid valve with total on hand to pull, you must first send electricity to manually open solenoid valve, solenoid valve will be closed and vice versa total. 6. fireman not mess-tune the burner, abnormal promptly notify management personnel, approved by management and then make adjustments. 7. In the long-term shutdown state, to do maintenance work on the boiler equipment, for each transmission parts to clean, lubricate.

WNS is automatic gas (oil) parameters commonly used 42 mw liquefied petroleum boiler in indonesia. Where each letter implication is that

W: horizontal. A boiler according to the design and installation of the outer layout, was lying state. An exhaust gas stream produced by the boiler is of horizontal flow, the flow of hot gas, in the same section on the exhaust gas temperature is low compete.

Factors affecting the energy saving heating 42 mw liquefied petroleum boiler in indonesias What are the reasons 1, strictly control the temperature of the boiler exhaust gas boiler heating some of the heat loss, exha reduce flue gas heat loss is an effective way to achieve energy-saving heating boilers. There is a certain temperature difference between the outdoor air temperature and the exhaust gas temperature. When the outdoor air temperature is lower than the exhaust gas temperature, exhaust heat loss is generated. Accordingly, the heating boiler exhaust gas temperature should be strictly controlled within the controllable range. If the exhaust gas temperature is too high, if the exhaust gas temperature is too low may increa, it will lead directly to the heating boiler running cost increases, which is due to the increased tail heating surface, so that the exhaust gas temperature as low as possible. In the energy saving work boiler should be carried out technical accounting and economic accounting. Accounting based on the dew point of the smoke, the tail heating surface and heat loss due to the consumption of the metal. 2, the carbon content of the slag reduce heating boiler First, the operation of the heating boiler in order to ensure the heating boiler that burns coal, the coal particle size be controlled, full use of coal resources, while achieving the purpose of protecting the environment. Secondly, reasonably boiler operating parameters adjusted to reduce the carbon content of the slag, that the ratio of coal to air is more reasonable and the coal before combustion in the furnace. Furnace temperature is a key factor in the index reflects a lot of energy-saving operation of the boiler. The carbon content of slag is one of them. In order to ensure energy saving heating boilers, efforts should be made to reduce the carbon content in the slag, timely elimination of negative factors affecting the normal combustion boiler. 3, the outer surface of the boiler furnace control temperature of the boiler size of the heat affected second two factors is the temperature of the boiler outer wall. It is also important for the outer wall temperature of the boiler, the influence of the external surface temperature of the boiler heating boiler. Relatively larger exterior wall area, the higher the temperature of the external walls, the greater the amount of heat to the surrounding environment. To reduce the heat radiation loss of a boiler, the boiler must be controlled outer surface of the body temperature. 4, to improve the thermal efficiency of the thermal efficiency of the heating boiler heating boiler is a comprehensive index of energy-saving measures. Improve the thermal efficiency of heating boilers, but also help to improve energy efficiency and heating boilers. Improve operational level boiler operator, control of boiler operating conditions, timely maintenance heating boilers, heating boilers to save energy. 5, timely monitor the operation of heating boilers timely monitoring of the operation of heating boilers, not only improve the operational efficiency of the boiler, environmental protection can not be underestimated. Different boiler room should take different measures, timely monitoring of the operation of heating boilers. Spread the boiler room should be checked by installing equipment, computer monitor should focus boiler room.

Jingzhou City, Hubei is located in Jianli County Supervisor Bureau for a food processing plant emergency inspection and maintenance, the timely processing of the security risks of the 42 mw liquefied petroleum boiler in indonesia. At the meeting held later, the city supervisor Bureau emphasized the specific guidance boiler safety management.