mechanical natural gas vacuum boiler manufacturers

What are the advantages slip parameter Henan gas mechanical vacuum boiler manufacturers unit? Henan gas boiler and turbine generator and start, while boosting boiler ignition, a low boiler parameters using superheated steam turbine to warm up increases the speed with load. Since the Turbo is warm start parameters steam temperature in the case of changing the vapor pressure and the like. Increases the speed. And a small amount of network and receiving the load, so called sliding start parameters, also called kit or unit is started. Many advantages: (1) start with the machine compared furnace separately, from the start to the unit with a full load, the time required is greatly reduced. Each turbine and boiler start-up time required, Henan gas boiler steam turbine start-up and the time required for the individual. And the time required for the steam turbine startup parameter sliding substantially equal to the time required for a single start, even shorter. (2) Since the parameters of the low initial start Henan gas boiler superheater outlet exhaust steam is used to warm recovered heat increases the speed and working fluid losses and part load, caused by exhaust. (3) warm the pipe warm lower pressure and temperature steam, thermal stress is much smaller than with the higher steam temperatures and pressures warm the pipe warm. (4) started separately, since the initial rise fire, the steam superheater is not cooled, burn-out to prevent overheating, you must limit the amount of fuel entering the gas boiler Henan. And slippery start parameter, starting with a vacuum in the condenser, soon there superheater steam cooling, Stokes speed can be significantly faster. At low pressure, large volume flow in the steam superheater, superheater tubes is not as small as the exhaust flow rate (about 15% to 20% of the rated evaporation), the flow rate variation when thermal image is generated individually activated deviation. (5) Sliding Parameters, Henan gas boiler starts to meet the requirements of the turbine increases the speed of the warm-up, because of the time needed to start a steam turbine is sufficient for the boiler. Adjusting the intensity of combustion boiler can be used (i.e., a control quantity of fuel into the furnace) to control starting conditions. When sliding pressure starting, due to the large volume flow of steam, it is advantageous to improve the water cycle and steam drum wall temperature difference from top to bottom.

Hot water mechanical vacuum boiler manufacturerss, electrical control box may not be water vapor or flammable gas and electrical control box may not be water or steam and flammable gas, shut the door 6,7 good cabinet in the boiler operation, when using the boiler, to ensure replenishment of water inside. Remove the monthly level sensor cleaning prevents the low water level sensor water level should not affect the normal operation of the boiler. 8, boiler stop a long running time, cut off the power, while the water in the boiler tubes put the net, to prevent frost damage, rusting. 9, through "Listen, smell, see, touch," do normal maintenance of the control box, such as abnormal phenomenon should immediately cut off the power timely maintenance. 10, periodically heating tube fastening nut and the screw connections on the flange, to prevent overheating of the oxidation loose, even burn line. 11, the scale on the heating tube is attached easily, especially in hard water, more fouling. If there is no electric water boiler softening equipment, it recommended every 30-40 days, heating pipe disassembly for scale removal process, if the heating treatment equipment should be disassembled for a descaling process tube 6 months. Replace the heating tubes should pay attention to the connection restoration, replacement of bad sealing gasket, good fastening screws on the flange, the fastening screws should be fastened symmetrically repeatedly tightened in order to avoid water leakage. 12, when not the usual boiler, cut off the power, the control box is opened, check all the electrical connections of the nut member, looseness should be tightened to prevent bad burning ignition wires and electrical devices. The body may have a dry boiler maintenance can have a wet maintenance. Letter user 2, boiler water quality should comply with GB1576-2001 "low-pressure boiler water quality," the. When required because of the use of forced overpressure, vacuum measures must be used so as not to exceed the specified pressure. 3,4,5,6, for safety reasons, the boiler must be grounded. Boiler room must be well ventilated to ensure that the boiler house and its surroundings must not be placed flammable and explosive materials. In order to prolong the service life of the boiler and the heating pipe, it is recommended to install on a silicon Regent softener inlet duct. 7, all of which run the boiler, the furnace body should always check furring scale, if the local labor offices should contact quality dosing station or pickling treatment, or because the user does not perform desmutting treatment furnace to cause local overheating causing cracking furnace, the consequences of the users themselves. 8, when the non-blocked drains installed.

Henan miss you Jujube Industry Development Co., Ltd. is mainly engaged in dates, nuts and other healthy food research and development, procurement, production and sales operations; jujube industry's first listed company. I miss you date industry is committed to providing health and hygiene products for people to date, in 2017, I miss you date industry decided to buy a few new clean and green, can provide high-quality steam mechanical vacuum boiler manufacturers steam. Carefully selected is determined in cooperation with the fast boiler, signed two separate 10 tons of steam condensing gas steam boiler (WNS10-1.25-Y.Q).

Several vacuum pressure gas discharge energy mechanical vacuum boiler manufacturers substantially in China reason to catch coal gas work, the application of vacuum gas boiler, a very large reduction of fouling contamination, together with nitrogen oxides and other health effects of gas He won the curb. Energy labeling is an important measure vacuum gas boiler, well that is that we begin to study the energy consumption of gas under pressure vacuum boiler several reasons. After investigation, the relevant departments of the gas boiler vacuum heat loss is probably produced in these two places included: full combustion flue gas emission values ​​are not as well as heat loss. Emission reduction of heat loss to be recycled at the end of the assembly setter exhaust gas heat recovery boiler in vacuo or more application functions leading condensing boiler. Value is not over the full combustion substandard summary: Select the common gas ejector type vacuum boiler burner, leading to the air-fuel ratio can be adjusted to maneuver. A majority of the gas is chosen vacuum boiler burner exhaust mechanical strength, air-fuel ratio over the reasons leading to the following aspects: air-fuel ratio does not contain over about two cases: when the airflow in excess, there will be over-full cold heat is conducted to increase the operating costs incurred by the gas boiler vacuum, reduced energy consumption vacuum gas boiler; when the airflow is not enough, there will be insufficient to ignite the situation, resulting in reduced energy consumption of the gas boiler vacuum.