Energy Saving Manufacturers coal fired steam boiler Brunei

Steam boiler accident type and processing method, and use common sense safety boiler energy saving manufacturers coal fired steam boiler brunei accident type and processing method, overpressure accident 1 boiler, boiler overpressure phenomenon of (1) a sharp rise in steam pressure, exceeds the allowable working pressure gauge pointer over " red line "safety valve after the pressure is still elevated. (2) the operation of the device is the interlock overpressure protection, should send overpressure alarm signal, stops the air blowing, the wind, coal. (3) steam temperature and steam flow rate reduction increases. 2, to treat boiler overpressure (1) weakened rapidly burning, manually open the valve or bleed valve. (2) increase the water supply, while the lower reinforcing blowdown drum (It should be noted at this time to maintain the normal water level of the boiler), in order to reduce the temperature of the boiler water, thereby reducing the pressure in the boiler drum. (3) as a safety valve malfunction or all of the pressure gauge damage, emergency shutdown, safety valves and pressure gauges are to be repaired after the boost operation. When endanger the safe operation of (4) Boiler excessive pressure, blood pressure should take measures, but too fast buck is strictly prohibited. (5) boiler overpressure eliminate serious, to the shutdown of the boiler internal and external inspection, to eliminate the overpressure caused by deformation, leakage and other safety accessories and maintenance unqualified. Second, an accident boiler water, boiler water shortage (1) below the minimum safe water level line, or can not see the water level, the water level gauge glass (plate) as a white. (2) as a full-color water level gauge vapor instruction color. Low water level alarm signal (3) water level alarm occurs. (4) low water interlocking means, the water level should be below a prescribed value blower, Fan, grate reduction motor stops running. (5) a sharp rise in the superheater steam temperature, higher than the outlet steam temperature. (6) boiler exhaust gas temperature rises. (7) the water flow is less than the steam flow, causing Should the water tube due to tube cracking or economizer, an opposite phenomenon occurs. (8) When a serious water shortage, can smell the burnt smell. (9) When a serious shortage, the door can be seen from the red-hot waterwall tubes. (10) a serious water shortage, the furnace tube may rupture, then can hear the explosions, smoke and steam from the door, watching spray the fire door. 2, boiler water treatment (1) through the "waters", sentenced to severe water shortages, emergency shutdown must be prohibited blind to the boiler feed water. (2) through the "waters" sentenced to a slight lack of water, it should reduce fuel blast, the wind, and slowly feed water. Third, full water boiler 1 accident phenomenon (1) above the maximum allowable water level line, or can not see the water level, the water level gauge glass (plate) dark color boiler filled with water. (2) all of the water phase as a color level gauge indication color. High-water alarm signal (3) water level alarm occurs. (4) decreased superheated steam temperature. (5) water flow is not normally greater than the steam flow. (6) water in a large number of sub-cylinder, severe trap operation. (7) with a large amount of water steam severe, increased salinity, water hammer occurs in the sound of the steam pipe, the steam connection flange outwardly dripping take place. 2, boiler full of water treatment rinse water table, determined to be minor or serious full of water full of water. Method: Close water table, the water pipe connected cock, then open drain cocks As can be seen from the decreased water level, indicating a slight full of water, the water supply is stopped, the drain valve open, put to the normal water level. Such as severe filled with water due to take emergency shutdown measures.

At 10:00 on September 6 and more, Harbin, a business is the purchase of a new boiler equipment installation, commissioning process when staff at a boiler pressure gauge index found that the performance of the boiler abnormal, but not so the commissioning personnel when the next step, a sudden loud noise, boiler explosion, a huge flame and furnace pressure debugging of oil spray everywhere, four commissioning personnel are subject to varying degrees of injuries, was taken to hospital for treatment .

Boiler is an energy conversion device, by entering the fuel to the boiler, chemical energy, power, etc., outputs a constant steam heat, hot water or organic heat carrier, to provide support for the heat industries. Meanwhile, the boiler is also a special equipment has a certain risk, when the boiler installation, commissioning, operation, etc., be sure to boiler operation safety first.

Now, Xiao Bian to operational safety considerations gas boiler summarize, we can refer to.

First, start, boost, steam supply

1, before the start of the preparatory work

Internal and external check: Check boiler, burner, a good state of the accessory device; action safety accessories, each of the valves, such as flexible instruments, the correct position.

Check the line voltage to meet the requirements, a variety of normal switch position, respectively, various auxiliary pump starts operating, the burner fan, oil pump is normal.

Boiler Feed: exhaust valve opening, to ensure the normal water level (just below the water level).

2, start

Firstly purging the furnace, induced draft fan suction time is usually about 10 minutes to ensure that no residual gas in the furnace, passing substitutions, and ignition for combustion air supply.

After firing is completed according to the adjustment amount of load required for combustion, the boiler into normal operation.

During startup, to closely monitor changes in water level, water boiler accident or occurrence textile full of water accidents.

Second, the normal operation

1, the water level

Fuel gas-fired boiler water table should be the red line indicating the high, medium and low water level, the operation shall not exceed the maximum safe level or below the minimum safe level.

Rinse water table at least once per shift, when there is suspicion of running water, rinse should always check.

2, steam pressure

Red lines indicate the working pressure gauge should have, so sensitive and reliable, the trap should be flushed at least once a week.

3, safety valve

Safety valve should seal intact, no leakage; once a week manually (or automatically) emission test, and begin start pressure, opening pressure, reseating pressure and test time, participants, etc credited maintenance log book u, for future reference .

4, sewage

Proceed as boiler water quality requirements of water quality testing personnel under the guidance of class 1 or 2 times sewage, sewage incident not too long, generally no more than 10 minutes.

Sewage should (preferably when shutdown), should be closely monitored sewage water level changes, and pay attention to safety at the time of low load, low pressure, high water level.

Many boilers when sharing a sewage mains, while sewage is prohibited.

Third, shutdown

1, the normal shutdown

After normal boiler shutdown should generally be reduced boiler load operation, press the boiler shutdown procedure. Actuated pump water to high water level, pressure steam boiler to be dropped after 0.3MPa flushing water table and sewerage operations, and finally close the raft, cut off the power supply control cabinet, wipe equipment, clean up the environment and health, For water, the water temperature should be below after 70 ℃, before proceeding.

2, emergency shutdown

When the boiler operation in the following situations should immediately shutdown:

Furnace water level drops below the minimum water level gauge visible edges.

Increasing water supply and other measures, but digital still continue to fall.

Boiler water level exceeds the highest visible water table level (full of water), the water still can not see the water level.

All water supply system water pump failure or malfunction, not water to the boiler.

Water gauge or safety valve all the failures.

Endanger the boiler element is damaged and the safety of operating personnel.

Combustion equipment damage, or furnace wall collapse and other red-hot boiler structure is a serious threat to the safe operation of the boiler.

Other anomalies endanger the safe operation of the boiler.

3, maintenance

Before maintenance work should be well prepared, as before entering the drum interior work, must be of sufficient strength to connect all of the metal blocking plate spaced reliable steam, water, sewage and other operation of the boiler pipes, and the drum manholes and hand holes (boiler shell) is opened, so that air convection period.

After the completion of preparations to repair. Should ensure that the quarterly frequency of boiler maintenance and repair of the year.

Advances in technology to the boiler industry into new and innovative ideas, now the boiler manufacturers boiler are easy targets toward the operation forward, but in the use of the boiler, improper operation or other quality problems still exist, these failures will It is causing the direct cause of the explosion boilers. Therefore, when using the boiler must be in strict accordance with safety practices boiler, security incidents strangled in the cradle.

Necessity textile mill converted to a coal-fired boiler gas boiler is a boiler equipment industry needs is more important, because a lot of links to the papermaking process requires a lot of steam drying, stereotypes and so on. However, along with the national policy of environmental protection departments to ban coal-fired boilers, and now more and more manufacturers have to use coal-fired boilers to coal-fired boilers upgrading or purchasing a new low - NOx emissions. Mills from coal to gas boilers is an important direction of the current transformation of coal-fired boilers, is one of more types of enterprise transformation, especially in the area more natural gas, coal into gas boiler is the main way. 1, in order to transform mechanization layered fired boiler gas boiler, you should first remove the front arch and a rear arch, while increasing the bottom heating surface, instead grate, grate to prevent overheating, combustion; 2, through the furnace heat transfer calculation methods determining the size of the boiler, furnace flame center position, and then pouring furnace work. In order to avoid the center position after arch boiler tubes, based on the original slope of the original arch made pipe. 3, the furnace in order to prevent an explosion, when the coal-fired boiler furnace gas is substituted, or when fuel not atomized combustion gases in the furnace incomplete combustion or heating surface of the end of the furnace, a fire or explosion occurs, should be mounting the appropriate parts of the boiler explosion vent, and to increase the ignition and flame failure protection program control to automatic control means, to ensure safe operation of the boiler. 4, is closely related to the selection and arrangement of the burner and furnace, the filling degree of the flame in the furnace should preferably not to form a dead air. Gas burner arrangement considered reasonable and piping layout, convenient operation, inspection and maintenance;

Steam boiler buying guide and cautions because the energy saving manufacturers coal fired steam boiler brunei is an extremely easy to use and very clean and environmentally friendly boiler, so it is widely used in various fields, and very loved by the people. We buy when the steam boiler, it must first be checked in detail, to see its various parts is normal, and make sure it's good quality. From the perspective of traditional economic and energy structure of China's point of view, gas boilers due to the low one-time investment costs of popular people favored, especially in the rich coal resources, environmental protection and less demanding areas people prefer to select it. But in resource-poor coal, coal prices are not low areas of oil, gas and coal compared to a certain competitiveness. Another reason people like coal stove is easy to operate. But gas-fired boiler pollution: waste, emissions, waste water, "three wastes" and taste, governance Yijiao difficult (especially desulfurization, the current gas boiler desulfurization technology has made some achievements, but the high investment costs, operation complex, large area) from a social perspective should limit the use of gas-fired boilers. Gas boilers efficient, clean, environmentally friendly, without manual operation, only need to monitor, small footprint, no need to transport fuel, no need to deal with soot, due to natural gas combustion no impurities, no corrosion damage to boilers and related accessories, boiler long life , defined as 15 years, but basically long-term use. Is now mainstream boiler, natural gas is the environmental protection sector, the government vigorously promoted. Many have been using coal as the heat source of industrial companies now use gas stoves geographical mandatory requirements, it may be gas steam boiler threshold will be higher in the future to strengthen environmental protection efforts. Soot emissions from oil-fired boiler, although lower, but its emissions of harmful NOX, SOX gases are causing "photochemical smog" and acid rain culprit, to be governance as soot emissions as gas boiler control. Gas boiler with a small footprint, less pollution emissions advantages, but also the cost of the boiler room is not set up, the use of natural gas fuel prices, operating costs lower than oil-fired boiler. By comparison of three of the furnace, gas boiler not only set a lower cost and operating cost, and its social benefits are incomparable. Natural gas is the cleanest fuel, is the least polluting fuel emissions, gas-fired boilers will be the development trend of boiler final.