gas boiler factory for thailand

Fuel gas control step and the blowing process air volume of the total fuel gas steam boiler factory for thailand steam boiler is achieved by adjusting a liquid coupling scoop blower. Organization fuel gas steam boiler combustion, is to make a, air pressure, air flow of secondary air with the good. Adjusting the amount of primary air should meet it carries the fuel into the furnace ignition of volatile oxygen required, and to maintain a certain speed, and without clogging the fuel discharge pipe of the jet having a certain rigidity. Primary air volume is too large and too small, the wind speed is too high and too low, should be avoided. In addition to adjusting the secondary air of combustion of the fuel should ensure that the oxygen demand, but must maintain a certain wind speed and primary air is mixed with the master time should have a strong stirring and mixing coke penetrate "the Gray" kinetic , which requires the case may be, each layer of the secondary air flow rate, in order to achieve stable combustion and flue gas excess oxygen appropriate destination. Fuel gas steam boiler, secondary air with what is better? Primary air volume air volume of the total share is called the primary air rate. A small air fraction, pulverized coal is heated to at least the heat required for the ignition point, fire faster, but the amount of primary air to satisfy the principle of combustion of volatiles. Secondary air mixed with the primary air time to the right. If it is mixed before ignition, means an increase in the amount of primary air, so that the ignition delay; hypoxia combustion secondary air if mixed will make late after ignition; if secondary air is mixed all at one position, since the secondary air temperature well below flame temperature, the flame temperature decreases, the combustion slows down, causing the fire. Therefore, the secondary air mixed with fuel should be based on the nature of the combustion zone as required timely sent, so that the combustion of oxygen, and will not reduce the flame temperature to ensure complete combustion and ignition stability. One or two wind speed with what is better? Fuel gas steam boiler once the wind speed is high, the fuel gas stream will catch fire in places far away from the burner, the ignition point postponed; once the wind speed is too low, it will cause a blocked ducts, and ignition point is too far forward, the burner will burn , but also easy to coke near the burner.

Recently, Henan Province issued the "2019 Henan ecological ideas and points", as follows.

1, the implementation of "winning Blue Sky Battle three-year action plan," "Henan tackling pollution prevention three-year action plan." We continued to do a good job in controlling coal, discharge control, train control, oil control, dust control, control burn "six control" based on the prominence of coal consumption reduction, optimize the industrial layout, transport restructuring, diesel trucks governance, urban dust remediation industrial upgrading green, clean heating construction, ecological expansion speed, enhance monitoring capacity, heavy pollution 10 iconic battles weather control and so on.

2, 2019 to promote the implementation of planning, environmental impact assessment and other "unified" requirement, in principle, then add the non-power sector coal consumption province-wide project to promote the transformation of shutting down coal-fired units and behind the irrational total of 1.5 million units kilowatt. Promote political urge the main town of coal units cleared and the main city of Luoyang coal units basically cleared. Do a good job clearing the continuing dynamic "scattered dirt" comprehensive improvement of enterprise and small coal-fired boilers. Township units continued to carry out an intensive investigation, the implementation of inventory management, network monitoring, inspections normalization mechanism, to treat small coal-fired boilers, found together with the ban.

3, already verified "messy dirty" business, in accordance with the principles of the rule after the first stop, the implementation of classification prosecuted. Do not meet industrial policy access, industrial layout planning, outdated equipment and technology, and no hope of treatment compliance, implementation of the "two off three clear"; the inclusion of the relocation of integration classes, in accordance with the principles of large-scale development, relocated to the industrial park and the implementation of upgrading; upgrading the inclusion of the class, set the industry benchmark, the implementation of cleaner production transformation, to raise the overall level of pollution abatement.

4, advancing the steel, aluminum depth treatment with carbon, cement, glass, coke, aluminum and other key industries. Deepen industrial enterprises fugitive emissions control, industrial furnaces special treatment, comprehensive treatment of industrial boilers, foundry industry depth governance, strengthen the petrochemical, chemical, packaging, printing, industrial painting and other key industries of volatile organic compounds pollution.

Recently, I saw a news about oil gas fired power plant boiler factory for thailand in Nigeria. The article talking about the first phase of Nigerian gas fired power plant inaugurated.

How to prevent corrosion of the gas boiler factory for thailand gas boiler it if the temperature is too high, some of the components of the boiler working long hours in the intense heat of the environment at work, the situation will cause boiler corrosion occurs. So, we are in the process of work what to do to reduce the corrosion of it? Here to tell you about some of the methods of preventing corrosion of boiler gas. Reason and approach demands on internal corrosion of the gas boiler must be in accordance with the methods and principles of conduct, you can now use a more extensive domestic and international gas boiler corrosion detection approach is magnetic flux leakage and ultrasonic detection. Ultrasonic Ultrasonic detection is used to measure the wall thickness after etching using the principle of ultrasonic pulse reflection. The basic principle of magnetic flux leakage method leakage flux detection method is based on the high-permeability properties of the ferromagnetic materials, magnetic permeability of the gas boiler corrosion disadvantage is much less than the permeability of the furnace, the applied gas boiler is magnetized in a magnetic field effect, when the furnace is no disadvantage, most of the magnetic lines of force through the pipe. Uniform distribution of lines of magnetic force at the moment; when the internal elbow has the disadvantage that the onset of meander lines of magnetic force, and a part of magnetic lines of force from leaking out of the outer steel pipe. Detecting the escaping magnetic flux leakage outer elbow, it can be determined whether the shortcomings exist. When the probe detects a straight guide hot oil furnace inner wall emit ultrasound pulse, to receive from the probe first reflected pulse within the outer wall, and will receive the ultrasound probe, this pulse and the pulse reflected from the outer wall of the outer appearance of the reflected pulse trip distance between the reflecting wall thickness. Gas-fired boiler in accordance with the practices and conditions set forth in the demand for the detection of practice, in accordance with the detection of ultrasonic inspection method can be distinguished way. High temperature components such as a gas boiler front panel, convection superheater and reheater temperature is the primary structural member and the like inside the boiler, a very long time to work in the harsh environment of use of the medium flame, smoke, ash, etc., and therefore the working process changes occurred in the organization and function of a range of materials, these changes hit the gas boiler creep, fatigue, corrosion, erosion and other messy aging and failure mechanisms. These high temperatures Microstructure component material will follow the extension of working time deteriorated creep damage occurs, such as loose pearlite, spheroidized carbides, grain boundary and growth mobilization, holes creep, intergranular cracking occurs .