gas steam boiler Commercial Factory Price Jordan

Why hot water boiler heating more energy efficient, more environmentally friendly: generally used for heating hot water boilers, but the need to use less steam production process. Biomass boiler categories: biomass boilers Horizontal, vertical biomass boilers. Biomass gas thermal oil heaters, biomass steam boiler commercial factory price jordan, biomass hot water boiler, biomass oil furnace. Steam boiler is an energy conversion device, the energy input to the boiler fuel chemical energy, electrical energy, thermal energy and other forms of high temperature flue gas, and after converting the boiler, the steam output having a certain outside thermal energy, high-temperature hot water or an organic carrier. Because it is more energy efficient than steam boiler, more environmentally friendly. First of all, in terms of fuel consumption, hot water heating than the steam boiler heating savings of 20% to 40% of fuel, this amount is very impressive. Summed up for two reasons: First, it does not condensate and heat loss due to evaporation of the secondary, two hot water heating pipe is heated by the use of special materials, as thin as possible to meet pipeline needs, heat loss is small. Heat loss due to the steam heating pipe caused by steam leakage large.

Hot water boiler which is not equipped with no impact can cause demineralizer 1, the waste fuel boiler fouling occurs, resulting in poor heat transfer performance of heating surface, so that heat generated by the combustion of the fuel can not be timely delivered to the boiler water, but a large amount of heat is smoke away, resulting in exhaust gas temperature is too high, if the exhaust gas loss increases the thermal efficiency of the boiler will be reduced. In order to maintain the nominal parameters of the boiler, fuel must be increased, thereby wasting fuel. About 1 millimeter scale waste fuel ten percent. 2, the heat receiving surface is damaged due to deterioration of the heat transfer performance, fuel combustion heat is not quickly transmitted to the boiler water, resulting in the furnace and the flue gas temperature. Thus, the temperature difference on both sides of the heating surface increases, the metal wall temperature, a decrease in strength. Under pressure pot, bags and even blasting will occur. 3. Reduce heat boiler output due to the deterioration of the performance of boilers, need to consume more fuel to reach the nominal rate of evaporation. However, with the increase in the scale thickness, the volume of the furnace becomes large, the fuel consumption is limited. Therefore, it is possible to reduce the output of the boiler. 4, the corrosion damage to the metal: oxygen in the water, acid, base materials will corrode the metal surface of the boiler, it is thinned, recess or perforation, thus reducing the power of the boiler, seriously affect the safe operation of the boiler. 5, in addition to improper operation Priming outside, when the boiler water contains more sodium chloride, sodium phosphate, and silicides oil, boiling or evaporation process boiler water, boiler water occurs when soap and organic base when Teng because soda will produce compost. Foam liquid surface, formed soda pool. No softening, easily scalable. Due to the continuous evaporation steam, boiler of calcium, magnesium, high impurity concentration is 30-50 times that of natural water, fouling rate beyond our imagination, only six months to a year, from 1-2 mm.

Principles of steam boiler commercial factory price jordans and solutions hydraulic external gear of Henan fast boiler's small series with you about the principles of steam boilers and solutions Steam Boiler hydraulic external gear in accordance with the fuel (electricity, oil, gas) can be divided into electric steam boilers, oil three kinds of steam boilers, gas and steam boiler; constructed according to the steam boiler can be divided into vertical, horizontal steam boiler, steam boiler compact than a single, double return of the vertical structure, large steam boiler return of more than three horizontal structure . If the classification according to top standards, in the form of steam boilers on the lot, would like to give an ordinary packaged boiler say four tons vapor. Water in the steam drum is heated to become vapor, fire emits heat in the furnace, it is the principle of the steam boiler. Steam boiler combustion section and drive means by a chain grate, a combustion chamber together with the pan rack frame formed on a grate composition. Four weeks envelope refractories. From coal fired into the hopper, the shutter coal front portion while sealing air control seam thickness. Blowing into the combustion chamber is a lower place, such steam boilers greater resistance, require forced air. Steam boiler cinder burn out, the rear portion of the grate by the "beak iron" discharged from the slag out of the furnace feeding machine. Steam boiler flue gas from the back of the boiler, the steam drum of a boiler return line before the smoke tube, returned by two return rear smoke tube, and then into the dust separating ashes, and then discharged through the chimney draft fan. These are the works of steam boilers, steam boilers run course, ultimately, other devices, such as induced draft fan not only bear the task of exhaust fumes, or negative pressure necessary for operation of the steam boiler. As well as pressure vessels, thermometer, safety valves, pressure gauges, pumps, steam pumps, and so on. They are essential for steam boiler work. Pump leaks. Gear pumps for leaks during operation, leading to its actual output is smaller than the theoretical flow of traffic. The main channel is leaking gear pump: through the gap between both surfaces and both side surfaces of the gear cover side leakage, accounting for 75% to 85% of the total leakage of the pump; radial gear tip circle between the inner hole and the pump CLEARANCE ; gap by engagement of the gear leak. The gear pump due to the presence of a leak, so that the output pressure do not increase, the influence of the use of a gear pump. In order to solve the low gear pump output pressure problems, may be employed on both sides of the elastic gear plus floating collar or baffle manner, to reduce the leakage of the gear pump, the gear pump to increase the output pressure. Radial force imbalance. In the gear pump during operation, the pressure acting on the outer gears are not equal, resulting in the gear and bearing at the axle radial imbalance force. This unbalanced force will accelerate the radial bearing wear and reduce the service life of the bearings, the gear shaft deformation can also cause friction with the inner hole of the addendum pump, pump damage, so that the pump does not work. The solution generally adopted is: ④ opening pressure balancing grooves to the pump, the high pressure oil introduced into the low pressure zone, but will increase the pump leak, the influence of the volumetric efficiency of the pump; ② size reduction oil pressure chamber, acting on the teeth the pressure area is reduced, thereby reducing the radial force imbalance.

Anyang City Minshan Nonferrous Metal Co., Ltd. is a collection of urban mining, renewable resources, energy as one of the economic wisdom of cleaning companies, mainly non-ferrous metal extraction and processing work. Company to conserve energy, cleaner production for the purpose of this concept coincides with the fast boiler. Thus, when the company in the purchase of the product boiler, and fast boiler almost hit it off, by the party to provide a fast 6 tons of steam integrally condensing gas steam boiler commercial factory price jordan (WNS6-1.25.Y.Q).