chinese wns horizontal oil steam boiler supplier

Gas boiler cook stove Note: As the boiler equipment kinetic energy sources in the manufacturing, transportation, installation and maintenance process will bring oil and other impurities, persist in the boiler, it will not only clog water pipes, deteriorating the quality of steam, but also will reduce the heat transfer effect, the heating surface prone to overheating cause burn. Therefore, for removing impurities boiling out this step, the stable operation of the boiler is an integral part.

Combustion gas treatment unit and a fault, gas boiler burner ignition misfire rod reasons: 1, the ignition bar gap interposed carbon residue with oil. 2, ignition rods fragmentation. moist. Leakage. 3, the distance between the ignition does not stick, too long or short. 4, ignition rods Insulation damage, short to ground. 5, ignition cable and transformer failure: cable, connector damage caused by a short circuit during ignition; transformer break or other fault occurs. Measures following five: Clear, renewal, adjust the distance, change and switching transformer. Second, gas boiler, but spark ignition rods misfire reasons: 1, the cyclone disc space ventilation is blocked carbon, poor ventilation. 2, dirty oil nozzle clogging or wear. 3, the throttle angle is set too small. 4, the firing bar from the leading edge from the oil nozzle tip inappropriate (too protruding or retracted) 5, the first solenoid valve is an oil debris blocking gun (gun small kerosene). 6, oily or too viscous to flow easily clogged or the oil filtration system the valve is not opened, so that insufficient suction pump, oil pressure. 7, the filter pump itself blocked. 8, the oil more water (boiling abnormal noise within the heater). Measures are: Clear; first wash, such as not renewed; turndown test; adjusting the distance (in 3 ~ 4mm as well); Remove cleaning (cleaning the parts diesel); Check tubing and oil filters, insulation equipment ; remove peripheral screw pump, carefully remove the cover inside out oil network, with immersion oil; renewal of the test oil. Third, when the gas boiler and turn the fire a small fire normal, off, or flashing instability reasons: 1, the air volume damper setting fire too. 2, oil fires micro switch valve (damper outermost that group) inappropriate setting (set throttle air flow rate is greater than the fire). 3, oleaginous easy to spray viscosity is too high (heavy). 4, and the nozzle plate spacing cyclone inappropriate. 5, fire nozzle worn or dirty. 6, the preliminary fuel tank temperature is too high, so that the steam not smooth oil pump oil feed. 7, fuel oil boiler water. Action: Test gradually reduced; heating temperature; adjusting the distance (between 0 ~ 10mm); clean or replace; approximately set to about 50 deg.] C; or drain oil change. Fourth, the noise increases gas boiler burner reasons: 1, cut-off valve is closed or the passage into the fuel shortage, an oil filter blockage. 2, the oil inlet temperature is low, the oil viscosity is too high or the temperature is too high the pump inlet. 3, oil pump failure. 4, fan motor bearing damage. 5, dirty fan impeller. Processing methods: ① the oil line check valve is open, if the oil filter is working properly, the filter cleaning pump itself. ② heating oil or reduce the oil temperature. ③ Replace the oil pump. ④ replace motor or bearings. ⑤ cleaning fan wheel.

July 26, 2016, Beijing, China Everbright Paper Co., Ltd. and the company signed a "split 6 tons of steam condensing gas chinese wns horizontal steam boiler supplier contract" by the company responsible for the WNS6-1.25-YQ split condensing gas boiler steam to all production, installation and commissioning work. The product is the use of condensing technology, effective emission of harmful substances SOx, NOx, COx, is industrial boilers efficient and environmentally friendly solutions.

609, why the chinese wns horizontal steam boiler supplier is replaced by electric heating gas steam boiler steam boiler is replaced why the electric heating gas furnace compared with the steam boiler steam, and the higher production requirements, pressure increases with increasing temperature. In recent years, new thermoelectric organic heat transfer oil furnace is also known as heat transfer oil furnace. we usually referred to as gas steam heater. it combustible gas and electrical energy to thermal conduction of the heat medium oil high oil outlet to 400c, heat device connected to the hot water more environmentally friendly and energy saving compared with the steam boiler, saving up to 40% to 55% oil furnace using electric heating and the conductive loop. different steam, the steam is directly discharged after use, heat can not be recovered heating stable, accurate temperature control. gas steam boiler and the heat transfer pipe are stable, unlike a steam boiler steam temperature fluctuations in the system, gas and steam electric furnace facilitate automatic control microcomputer electric heating oil heater low and high temperatures are secure, gas and steam heated to 340 degrees at normal pressure, does not evaporate. steam reach the same temperature, the saturation pressure 14.593MPa. hot water boiler must be in order to achieve a certain pressure High water temperature. If you want to get a temperature of 280 degrees Celsius, the pressure should be reached 6.412MPa. Therefore, gas steam heater has a good safety performance heat transfer oil furnace electric heating with low cost, low investment, easy to manufacture and so on. due to the low heat transfer oil furnace operating pressures, significantly easier to manufacture than the steam boilers and hot water boilers, low cost, small investment. in general, class E with twelve kinds of boiler or pressure vessel manufactured qualified manufacturers have the ability to produce hot oil furnace .609,