gas heating condensing water tube hot water boiler machine

Exhaust gas has been plagued by sewage paper industry, paper industry pollution problems of the country very seriously. Fujian Heng paper packaging company has been committed to the use of clean-type boiler paper processing. October 22, 2016, David Carse, the paper with my company, signed a 6 tons of steam an integral condensing steam boiler for the production of corrugated cardboard and other paper products. I provided the boiler greatly solve the problem of sewage wastewater Heng paper. After the boiler operation, both to meet local environmental requirements, but also reduce operating costs for the constant boiler paper products.

The development trend of environmentally friendly eco-friendly heating condensing water tube hot water boiler machine hot water boiler ushered in new opportunities. Late last year the State Council issued energy-saving environmental protection industry. Environmental protection boiler is also more and more attention in the boiler industry, in which major favorable policies, the mountain pot boiler seize the opportunity to develop environment-friendly hot water boiler, and its development trend did some summary for everyone to share now study and discussion, together with the conduct. The development trend of environmentally friendly hot water boiler specifically in the following areas: high-efficiency boilers; using simple auxiliary sets; simple structure; the whole intelligent automatic control and is equipped with multiple-level protection system. Environmentally friendly hot water boiler is on the whole have the following requirements: size and weight were reduced, which reduces the footprint of hot water boilers, boiler room would not need so much construction, weight reduction will saving materials, use of new materials to replace the old materials to improve the life of the hot water boiler, also during transport in many aspects, reduce unnecessary trouble. Improve boiler efficiency reduces fuel combustion, thus reducing the consumption of natural emissions of flue gas and water; and increase the degree of automation assembly, boiler maintenance so it will be more convenient, where you do not have the repairs carried out accessories and replacement is simple and convenient, automatic application of the procedures boiler with higher intelligence. Especially in recent years, the use of some new combustion technology and enhanced technology, the volume of oil and gas hot water boiler heat transfer is greatly reduced than before. Our industry has made great strides in development, people's general requirements of hot water boiler will be more stringent. This requirement is mainly to solve the contradiction between economic, security, usability. Mountains pot hot water boiler with a mature technical team, developed a hot water boiler in line with customer requirements for environmental protection, we have made many achievements in the hot water boiler market. Our mountain pot boiler satisfied with the existing results, as always, based on the market, focus on the future, to develop more high-quality environment-friendly hot water boiler, make a contribution to environmental protection. Gas boiler steam cleaning and maintenance measures combustion gas steam boiler is first opened the door, the rear housing panel removed, screwing the rear open boiler cleaning opening. Clean fuel gas piping with a wire brush. With a soft brush to clean the combustion chamber. Gas steam boiler to remove residue in the boiler, the cleaning opening is screwed on the screw, closing the burner door seal check is complete. If the boiler is installed in areas where temperatures below 0 ℃ must take the following precautions: If outside the boiler room, the room temperature drops below 15 ℃ or 18 ℃, the whole day operation of the boiler. If a long time no one in the room should be emptied of water in the boiler. You know cathodic protection of each member constituting the boiler (such as iron, copper, aluminum, etc.) of different materials. In order to prevent galvanic corrosion, cathodic protection measures must be taken. Sewage treatment boiler. The bottom of the gas-fired boiler flue gas emissions to prevent condensation. Since the flue gas is flue gas condensation (diesel or natural gas) and the flue gas temperature in the aqueous too low, water generated. A portion of the moisture is discharged from the chimney, the chimney wall is absorbed, the rest is deposited on the bottom of the chimney. Water produced by the following factors influence: flue gas temperature (efficiency 91%, the flue gas must be at a temperature of 170 ℃) where the total surface area heat chimney, chimney and chimney material. Maintenance of the burner. Gas boiler and burner maintenance, the best maintenance after steam supply. Because the products of combustion will corrode the boiler, clean up carbon deposits, therefore, not allow the products of combustion burner door opened first time in memory, leaving the boiler is too long, remove the rear housing panel, tighten the screws to open the rear side of the boiler clean mouth. Clean fuel gas piping with a wire brush. With a soft brush to clean the combustion chamber. Gas steam boiler to remove residue in the boiler, the cleaning opening is screwed on the screw, closing the burner door seal check is complete. If the boiler is installed in areas where temperatures below 0 ℃ must take the following precautions: If outside the boiler room, the room temperature drops below 15 ℃ or 18 ℃, the whole day operation of the boiler. If a long time no one in the room should be emptied of water in the boiler. You know cathodic protection of each member constituting the boiler (such as iron, copper, aluminum, etc.) of different materials. In order to prevent galvanic corrosion, cathodic protection measures must be taken. Sewage treatment boiler. The bottom of the gas-fired boiler flue gas emissions to prevent condensation. Since the flue gas is flue gas condensation (diesel or natural gas) and the flue gas temperature in the aqueous too low, water generated. A portion of the moisture is discharged from the chimney, the chimney wall is absorbed, the rest is deposited on the bottom of the chimney. Water produced by the following factors influence: flue gas temperature (efficiency 91%, the flue gas must be at a temperature of 170 ℃) where the total surface area heat chimney, chimney and chimney material. Maintenance of the burner. Gas boiler and burner maintenance, the best maintenance after steam supply. Because the products of combustion will corrode the boiler, clean up carbon deposits, therefore, not allow the products of combustion in the boiler stay too long memory

The fuel can be natural gas boiler into gas-fired, city gas boiler, boiler coke oven gas, liquefied petroleum gas boilers and boiler; functions can be divided in accordance with KS-Q water natural gas boiler, CLHS / CWNS natural gas heating condensing water tube hot water boiler machine (including natural gas heating boilers and gas boilers bath), LHS / WNS natural gas and steam boiler; can be configured in accordance with natural gas boiler is divided into vertical and horizontal natural gas boiler; flue gas flow can be divided according to a single backhaul gas three-pass boilers and natural gas boilers. Fuel oil-fired boiler is the difference between a fuel (such as diesel, oil, kerosene, etc.), natural gas boiler fuel is natural gas (such as natural gas, city gas, biogas as well as liquefied petroleum gas, etc.), depending on what fuel boiler combustion devices called burner, natural gas burner configuration called boiler natural gas boiler, oil boiler burner configuration called oil-fired boiler, oil-fired boiler and the difference between natural gas boiler that what fuel burners.

If you know a little about chemistry, you may know that the sulfur content of oil and coal is roughly equal, but ask what low-temperature corrosion of oil-fired boilers is much more serious than coal-fired boilers, for two main reasons:

1. 90% of ash in coal-fired boiler, especially coal powder furnace, is taken away by flue gas, sulphuric acid steam formed in flue gas is absorbed by fly ash in flue gas, so that sulfuric acid vapor in flue gas is reduced, and about half of sulfur remains in ash when coal is burned. When the oil is burning, the sulfur content in the fuel almost all changes to the ash in the SO2, fuel, the fly ash in the flue gas is very little, and the adsorption ability to the sulphuric acid vapor in the flue gas is very weak.

2. The hydrogen content of oil in the oil-fired boiler is about 11%-12%. The combustion of each ton of fuel oil can produce about 1 ton of water vapor, and the partial pressure of steam in the flue gas is higher than that in the case of coal-burning.