1 ton gas steam boiler Fully Automatic Cambodia

Gas boiler precautions required during installation methods, or steps :( a) a foundation base of the boiler should be provided is determined according to the local soil, manufacturers design reference by the civil sector again. After reaching the base strength boiler, the boiler should drawings inspection and acceptance, and to draw the whole boiler three reference lines: a, longitudinal reference line - drum center or the center of the combustion apparatus. b, lateral reference line - the center of the front axle or chain grate slag centerline of the machine. C, elevation reference line - can be selected from a number of locations about four weeks, respectively, on the basis of the marking, the relative offset between the markers should not exceed 1mm. Furnace in place. After assembly the lower part of the boiler in place first, then the upper assembly large, the upper and lower portions need to find a combination of two positive pads firmly, should be both inside and outside the two casting. Installation location and size deviation test methods according to GB50273 "boiler installation engineering construction and acceptance" implementation. (B) lifting the boiler, during lifting, should be suspended on a lifting lug drum boiler ready large, the boiler on a foundation base coincides with the pre-drawn reference line. The longitudinal centerline of the boiler and the foundation, the deviation is not more than 3 mm, and the inclination with the center line of the drum hammer correction, allowing the central drum inclination is not larger than 5 mm, otherwise use horns foundation base and the junction pad level. Maximum level (c) Installation of boiler network (1), water supply conduit installation requirements typically require as backup pool below the normal water level line of the boiler, so as not to shutdown, boiler feedwater flowing into a large number of drainage caused to start the next . At the outlet of the tank (i.e., an inlet feed line) should be installed wire screen. (2), a main steam line installation requires the main steam lead pipe straight run section should be more than 0.5 m, the bending radius should be 4-5 times the diameter of the pipe, the trap should be fitted at the lowest line in order to prevent water hammer pipe, while to be reliable insulation. (3), the safety valve should be installed in the valve installation requirements after the hydrostatic test, the safety valve shall be fitted exhaust pipe, the exhaust pipe of the safety guide outside the boiler house, allowed valving the exhaust pipe. (4), mounting a lower water table level table downcomer must access a safe place, Hancock rotating flexible water table, not leaking, water table must be installed to the lighting device, easy to observe. (5), a pressure gauge mounting means so that when the scale gauge vertical plates, should be painted red gauge scale to show the maximum allowable pressure boiler, rotating flexible plug gauge, not leaking, water flow, pressure gauges insulation prohibited. (Iv) the boiler chimney installation requirements, when lifting the chimney, the chimney should be straight, horizontal direction lead length should not be too long, generally less than 5 meters, the height of the chimney should comply with relevant national standards. To add chimney rain cap, the weight of the chimney should not fall directly on the boiler chimney take over the host. Installation (e) combustion system: 1, according to the combustion system of FIG power line control circuit, a control signal line and the control line is electrically connected, the program should be installed reliable ignition and flame failure protection devices. Combustion process controller provides a separate set of contact start-stop control. May be formulated in a variety of burner start-stop loop cascade control relay 10A is a fuse, relay start-stop control stops the control terminal may be connected to the burner, may directly control the power of the burner. Both constant pressure sensor, water power, fuel, gas pressure set value is detected after the automatic controller opens. Time pressure sensor, water supply, oil, gas, and their detection circuit, alarm and found the problem immediately shutdown flame protection, the controller automatically displays the point of failure, an alarm sounds machine.

First prize: second prize of Jiangsu Food Co., Ltd. Dali: Clean Energy Heating Co., Ltd. Tianjin Terry prize: Shenyang Institute of Urban Construction Asset Management Co., Ltd. Third prize: Baoji Geely Automobile Parts Co., Ltd. Third Prize: Markor international furniture (Tianjin) Co., Ltd.

Steam boiler 1 ton steam boiler fully automatic cambodia price Price: works steam boiler is heated in the drum and water is converted into steam, fire gives off heat in the furnace. Qiang boiler plumbing materials sales center is located in the southern suburbs of Datong City, is a design, sales, installation and service of integrated modern enterprise management. The main environmental operating boiler, a steam boiler fired boiler, a heating furnace, steel radiators, cast iron radiators, canned motor pump, the pump piping, air-conditioning water, galvanized pipe, PP board tanks. Details can be found! Works (in Pulverized example) in the furnace pulverized coal combustion heat is first absorbed water wall heat transfer by radiation, boiling and evaporation of the water wall to enter a large amount of steam for steam separator drum (excluding the DC furnace), into the separated saturated steam superheater heated by flue gas at the top, and the horizontal flue gas flue continue to be absorbed radiation and convection, superheated steam reaches a predetermined operating temperature. Generating boilers usually equipped with a reheater is heated by high pressure steam cylinder. Reheater steam power generation is continued into the low pressure cylinder. 1, the working principle (as an example in pulverized coal fired boilers) in the furnace pulverized coal combustion heat is first absorbed water wall heat transfer by radiation, boiling and evaporation of the water wall to enter a large amount of steam for steam separator drum (except for the DC furnace ), the separated saturated steam enters the superheater heated by flue gas at the top, and the horizontal flue gas flue continue to be absorbed radiation and convection, superheated steam reaches a predetermined operating temperature. Generating boilers usually equipped with a reheater is heated by high pressure steam cylinder. Reheater steam power generation is continued into the low pressure cylinder. 2. Pulverized coal boiler operation, the position of the center of the flame will affect evaporation. Generally, low center of the flame will lead to greater evaporation, and the high center of the flame will lead to slow evaporation. Also affects the position of the center of the flame superheated steam or reheat steam temperature. Typically, superheated steam, in particular the reheat steam temperature in the lower center of the flame, and vice versa. 3. Pulverized Coal Burner front and rear walls is arranged a thrust manner, tangential firing mode, bis tangential firing methods, each method has its own characteristics. Since the above-described arrangement can not be applied in the same furnace at the same time, the influence of steam can not be directly determined.

Gas fired boilers into boilers which benefit: the traditional coal-fired 1 ton steam boiler fully automatic cambodia in the use of the process releases large amounts of carbon dioxide, sulfur dioxide and other harmful gases, causing serious air pollution and acid rain, and coal are non-renewable resources, Earth the storage capacity is limited, and the price of coal is relatively high with the successive implementation of the national policy of reform coal, coal-fired boiler traditional high pollution and high consumption market gradually been criticized, many provinces and cities have started from coal to gas work, namely the traditional coal-fired boilers to become clean non-polluting gas boilers, and strive to achieve the unity of economic and social benefits. In conventional coal-fired boilers used in the process releases large amounts of carbon dioxide, sulfur dioxide and other harmful gases, causing serious air pollution, and acid rain, while the coal are non-renewable resources, the limited storage capacity on the earth, and the price of coal is relatively higher, therefore, imperative coal to gas has the advantage.