gas steam boiler Energy Saving Best Selling Cyprus

Our company in the choice of boiler products, attaches great importance to the quality of emissions and steam boiler energy saving best selling cypruss, boiler low emissions of pollutants party provides fast, good steam quality is superior boiler products. --customer feedback

Run time, and the thermal conductivity of the gas boiler gas boiler after its long run, inevitably its scale and corrosion problems in the use of the process, the main reason the gas boiler scale formation is due to the water with ingredients hardness, high temperature, high pressure continuously concentrated by evaporation. Gas boiler furnace in which it is running a series of chemical and physical reactions will occur during use will effectively form a dense and hard scale on the heating surface, which would lead directly to lower the heat exchange efficiency and due to corrosion under the scale factors, it will lead to reduced boiler water wall furnace heat absorption. The outlet temperature of the gas boiler furnace during the course of an increase, so that losses will increase in the boiler, it will be effective to reduce the heat transfer in the water wall fouling equipment, so it is very likely to cause the water-cooled wall tube wall temperature results in an increase of the thermal conductivity of scale squib gas boiler waterwall at runtime only a few tenths of a steel material, when its heating surface fouling, so that the heat transfer will be impeded, in use process in order to maintain a certain boiler output, it is necessary to raise the temperature of the fire side. During the washing process gas boiler which may be employed in an efficient and environmentally friendly non-corrosive cleaning agent for cleaning the boiler, so that the device will expose the metal tube primary colors, because the reduction of algae and biological sludge fouling effect. Note that after the need for effective gas boiler furnace during ignition of smoke was observed and the temperature of the main steam temperature, the case where the pressure rise of the main steam, which is encountered after the boiler ignition temperature of tobacco will significantly increase the speed of the smoke or temperature Pianman It does not rise to the herd to immediately check the oil gun fire conditions.

Gas boiler heat loss through the combustion of fuel gas boiler, will release some heat, which will supply part of the user, some will be recycled and part is inadvertently wasted. So these are wasted heat lost through the ways in which it (1) heat losses:? Flue gas exhaust gas boiler part of the heat into the atmosphere, causing the boiler heat losses, it is each boiler term heat loss Dazhong biggest one. The main factors influencing the heat loss is higher exhaust gas temperature and the amount of smoke exhaust gas temperature, the greater the amount of smoke, the greater the heat loss. Low exhaust gas temperature depends mainly on the number and operating conditions of the heating surface; the amount depends on how much leakage exhaust case and the furnace excess air, flue. (2) heat loss incomplete combustion gas: a part of the unburned combustible gas is discharged with the flue gas to heat loss caused by heat in the flue gas. The main factors affecting the incomplete combustion gas heat loss is the excess air and furnace structure. Excess air coefficient is too small, uneven air is mixed with fuel, easy to generate carbon monoxide and other combustible gases; excess air coefficient is too large, the furnace temperature is lowered, the combustible gas is not easy ignition and combustion. Furnace volume is too small, combustible gases in the furnace too late to enter the combustion flue gases caused by incomplete combustion heat loss. (3) heat loss: the furnace heat loss, frameworks, pipes, door opening caused by heat dissipation to the surroundings. Size depends on the heat loss factors of the size of the surface area of ​​the furnace gas steam boiler energy saving best selling cyprus, heat insulating properties and thickness, the outside air temperature and the flow velocity. Electric heating reactor common external damage: an electrically heated reactor despite external corrosion has a high etching resistance against acid and alkali resistance, but our electrical heating by the heating apparatus is a kettle layer and an outer tire iron constituted. Such a medium is iron acids and bases are not corrosion-resistant. If we would have the production process if the reactor cover or screwed pipe joints without seal failure or leak acid tire iron reactor apparatus for electrically heating the outer corrosion. Corrosion support member 2. The reactor was heated electrically heated reactor during installation, support or other support member may be mounted directly on the floor, due to the long manufacturing operations on the floor may be deposited with corrosive media, so that for support our reactor electrically heated apparatus corrosion, resulting in the supporting force of each of the support produces a change resulting in a change in stress in the damage produced during heating layer. 3. The electrically heated reactor stress spout in the electrically heated reactor, when the steel of the pipe and the pipe joint, since the thermal deformation and the reaction was heated electrically heated autoclave vessel or duct stressed cold might damage the pipe.

As to 10 ton LPG gas fired boiler, here “10 ton” does not means the weight of this boiler, it means the boiler steam capacity per hour. Some clients may doubt the boiler only can burn LPG gas. Well, the writer reminds you this WNS series boiler can burn diesel oil, heavy oil, light oil, natural gas and so on. But this is designed to burn lpg gas, which means this boiler thermal efficiency can reach into highest level when burning lpg gas.