gas fired steam boiler manufacturer in rampur

Lanzhou City, Gansu Province, the transformation of coal-fired boiler control policy in accordance with the latest introduction of the "not big on the small" principle to give "Yijiangdaibu" financial support to owners of units, specific subsidies are as follows:

1, for a single 1 ton / hour or more than 0.7 megawatts of clean energy and coal-fired boilers by 100,000 yuan to subsidize steam tons of standard /.

2, coal-fired heating boilers mentioned standard governance and meet the national air pollutant emission limits in particular boiler, according to subsidize 50,000 yuan / ton steam standards, subsidies does not exceed 30% of the total investment quota.

3, for a single 1 ton / hour or 0.7 megawatts of utility units (including schools, health centers, hospitals, neighborhood or township government offices and other public units) clean energy transformation of coal-fired heating boilers in accordance with the actual heating area subsidies, allowances of 100 yuan / square meter.

Main contents of boiler energy efficiency test:

1. Boiler thermal efficiency test: a) determination of boiler evaporation; b) boiler excess air coefficient detection; c) exhaust smoke temperature detection; d) fuel combustion efficiency test; e) boiler thermal efficiency test; f) fuel consumption; g) Steam to coal ratio.

2. Boiler new product stereotyped energy efficiency test: Determine whether the boiler thermal performance indicators are consistent with the design and determine the operation mode of the equipment. Such as boiler evaporation, boiler thermal efficiency, combustion efficiency, various heat losses and so on.

3. Boiler operation adjustment test: Determine the most economical operation mode of the boiler and identify defects in the boiler operation. Such as boiler maximum load, boiler minimum load, fuel requirements, economic load, reasonable exhaust gas temperature, optimum wind coal ratio, excess air ratio, secondary air ratio and so on.

4. Comparative test of thermal performance before and after boiler reform: changes in evaporation, effects of combustion, thermal efficiency of boilers, etc.

5, fuel industry analysis, elemental analysis: to judge the quality of oil, gas and other fuels, easy for enterprises to control the quality of fuel into the plant.

6, water quality testing, scale analysis: determine the quality of water, control the boiler water indicators to prevent boiler fouling.

Thermal efficiency of coal-fired boilers and boiler standard reference card Is there a difference: in the specific types of boiler, the following will explain to, this kind of boiler coal-fired boiler, and its Web site or in the product, so it is very it is necessary to become familiar with and understand, so that, in order to have a comprehensive understanding of the product website, and also to broaden their knowledge and thus, in its study on the road forward. 1. oil-fired boilers and coal-fired boilers that heat the surface of the furnace, Is there a difference? Fuel oil and coal-fired boilers, which are two major types of boiler, the boiler is in this category, but they get hot surface of the furnace, there is a certain difference, is different, so the on this issue, that the answer is yes. In addition to an outer surface heating furnace, there are differences in other aspects. 2. coal-fired boiler, if it is less than 1 ton of steam, then, the thermal efficiency is how much is? Coal-fired boilers, if it is less than 1 ton of steam, then, the thermal efficiency of the boiler, within the range of 73% -79%, and want to obtain specific parameters, reference may be TSGG0002-2010 "energy saving technology Regulatory boiler regulations, "the standard to obtain accurate values. 3. General boiler certificate, if there is gas and coal-fired boilers of points? Coal-fired boilers, which are how many MW? General boiler certificate, there is no gas boilers and coal-fired boilers of points, so at this point, we should have a correct understanding, you can not go wrong. The MW coal-fired boilers, in general, is 0.35-7MW this range.

Released by the heating device (burner) heat transfer by radiation is first absorbed waterwall waterwall Boiling water, a large amount of steam into the drum for water separation (excluding DC furnace), separated saturated steam enters the superheater , and it continues to absorb the top horizontal flue furnace by radiation, convection, heat of the flue gas flue of the tail, and the superheated steam to reach the required operating temperature. Power generation boilers are generally provided with a reheater, it is used to heat the steam through the high pressure cylinders acting reheater go out of the reheat steam, the low pressure cylinder to continue to generate power. Popular terms, the fired steam boiler manufacturer in rampur is to absorb combustion heat of the fuel into the water some parameters (such as pressure, temperature, etc.) of the steam device. Boilers and boiler furnace divided into two parts, the pot is filled with water to a metal container, partially combusted fuel furnace, the heat absorption of the water inside the pot furnace fuel combustion converted to steam, with the basic principles of almost boiling water, the pot equivalent kettle, oven stove equivalent. 1, by fuel, our existing steam boiler fuel that can be used are: gas boilers, coal-fired boiler, oil-fired boiler, electric heating boilers, nuclear boilers, waste heat boiler, etc., of which the first four of the most common.