Fully Automatic 10t boiler Industrial Bhutan

The picture shows the fast fully automatic 10t boiler industrial bhutan processing plant located in the plain areas, plus catch up period is for a residential area of ​​Beijing for the production of low concentration of nitrogen product water tube boiler heating in winter, as scheduled in 2018 to ensure that heating at the same time, to meet the 20 mg / m require extremely low emissions of nitrogen oxides, Beijing air emission standards applicable to other regions 30 mg / cubic meter.

Henan gas fully automatic 10t boiler industrial bhutan installation requirements for the gauge 1. Pressure gauge installation should meet the following requirements: ⑴. Henan gas boiler installation position gauge, should be easy to observe and rinsing, the dial should be tilted forward 15 °, and should prevent affected by temperature, vibration and the like freezing. ⑵. There should be a trap between the pressure gauge and gas-fired boiler drum Henan. Steam or hot water in which the spring and then into the cooling pipe, to avoid reading errors caused by high temperatures, even damaged parts in the table. The inner diameter of the trap, with the brass when not less than 6mm, when using steel not less than 10mm. A lower portion of the trap, preferably equipped with drain cocks, water to let go of the tube after shutdown. ⑶. It should be fitted between the water gauge and the three-way stopcock elbow, and to flush the pipeline inspection, check, unloading gauge change. a. When normal working pressure gauge, Henan gas boiler media through the trap and pressure gauge connected, the pressure gauge pressure boilers. b. Check the pressure gauge, Henan gas boiler and pressure gauge cut off, the pressure gauge to the atmosphere, because there is no pressure in the table, so if the pointer back to zero can not prove that the gauge has failed and must be replaced. c. When flushing the trap, Henan gas boiler with the atmosphere, with the pressure gauge cut off, the trap in the water and dirt, the boiler blowing in the media. d. So that when water in the trap, the trap and the air pressure gauge are cut off, Henan gas boiler steam or hot water is gradually accumulated in the trap was cooled. e. When checking pressure gauges, while communicating with the boiler working pressure gauge and check the pressure gauge. Standard gauge calibration connected with the flange on the left side of the three-way cock, the medium from the working pressure into the trap and simultaneously checking the pressure gauge. Pressure gauge indicates the two values, the difference shall not exceed the gauge tolerances specified otherwise, the work proved inaccurate pressure gauge, pressure gauge must be replaced. Three-way stopcock handle end portion, the plug must be marked with an arrow indicating the direction of passage in order to identify. When the three-way stopcock operation, action to slow, to avoid damaging the gauge parts. ⑷. Even if long tube pressure gauge, the valve can be installed (or cock) close to the connection pipe at boiler drum Henan gas for use in the maintenance of the cutting gauge and accessories. However, in operation, the valve must be loaded (or tap) the hand wheel (or handle) Remove or lock to prevent accidental off and cause a major accident. 2. When the pressure gauge of the following circumstances, should stop using: ⑴. Limited nail no pressure gauge, the staple rotation pointer does not return to the limit; not limitation staple no pressure gauge, a pointer value from the zero position more than a predetermined tolerance gauge. ⑵. The surface of the glass or ambiguous dial scale. ⑶. No seal, the seal is damaged, or the Verify the expiration date. ⑷. In the table pointer leaks or beating. ⑸. Other effects gauge accurate defect.

Boiler Switch two cycle ways and explained why the use of compressed air: For the fully automatic 10t boiler industrial bhutan, through the front of the relevant articles, as well as knowledge of the contents of the article, we can gradually come to know and understand it, so as to achieve the desired learning objectives and learning requirements. Therefore, in order to promote the learning process, and so we have a new harvest, following that, the boiler will continue to explain, mainly some new knowledge content. 1. boiler cycle way, usually there? Boiler circulating manner, generally speaking, there are mainly forced circulation and natural circulation both. Forced circulation, the main, through the pressure boiler water circulating pump, to force performed. While natural circulation is achieved and the pressure head generated by natural drop tube between the boiler and the heating surface. Therefore, this kind of boiler, we will call it natural circulation boiler.

When gas heating fully automatic 10t boiler industrial bhutan maintenance methods outlined (a) gas heating boiler more frequently compared to winter season, then the application will not be need to be simple maintenance, the maintenance of gas heating boiler method, what does ? The following small series in which the first a dry regimen simple example set forth. Three methods of dry Maintenance method: (1) After heating boiler shutdown, we must first produced during the operation dirt clearing is completed, in the process should have a tubing connections with the outside world were cut block. (2) shutdown a long time, to the boiler rust maintenance, troubleshoot and repair their accessories in the furnace heating boiler and flue can be implemented dry lime boiler maintenance. (3) the use of a desiccant boiler during use to pay attention to the amount of control, but to do the water system of boiler and Flue Gas System and isolation to protect the outside world, so as to avoid the outside world into the water, causing the drying effect is reduced. In addition of course, there may be other details of the work and methods of dry maintenance, which requires the actual situation, selective use, to ensure maintenance of effect in a reasonable manner presented.