200kg gas steam generator

Heating boilers partial failure of boiler pressure controller controls the generator, because there is no water showed no the control circuit board, which is mainly controlled by heating the liquid level control float. When an appropriate amount of water, floating on control splendidly floating-point voltage, so that the boiler applied AC contactor work, start heating. This simple structure generator, the current market use more circulation. Such a generator common fault is not heated, mostly appear on the float level controller. First check the external wiring float level controller, whether the control point of the vertical line connected pair, and then split the float level controller, to see if it floats flexible. Then you can use the manual, the heat upper and lower part of the fault can be turned on by the control point whether the amount of the multimeter. After checking everything is normal, then check whether the water tank float. In other words it can float, i.e. the fault is rectified.

Throat automatic electric supply system of the 200kg steam generator, steam drying steady flow supplied to the user. When the water into the tank, the power switch, controlled by the drive signal, high temperature solenoid valve is opened, the pump work, is injected through the check valve furnace. When the solenoid valve, the check valve is clogged or damaged, the water pressure reaches a certain overpressure valve through overflow back into the tank, to protect the pump. When the tank without water or residual air in the pump piping, air not only into the water, as long as the rapid exhaust through the exhaust valve until the discharge water, close the exhaust valve, the pump will function. The main water supply system component is the pump, they use a multi-stage vortex pump of higher pressure and a larger flow rate, using a small part of the diaphragm pump or a vane pump. Stainless steel mechanical float level controller for generator furnace large volume, the working pressure is not stable, but easy to washable, maintenance and repair. Furnace boiler body generally use special seamless steel pipe, elongated upright. Most electric heating system or a heating tube used in a root canal curvature combination of stainless steel heating, while the surface load is generally about 20 W / cm. Due to the higher pressure and temperature when the generator is working properly, the safety protection system in the long run can make it safe, reliable and efficient. It is generally produced using high strength copper alloy valve, check valve, an exhaust valve, implement three protection. Some products also increased the water level in the glass tube protection device, increasing the user's sense of security. Product choice points: Electric steam boiler main control parameter is selected nominal evaporation, thermal efficiency of the boiler design, the rated steam pressure, the rated input electric power and the like. Use of electric steam boilers should meet the requirements of national and local restrictions related standards, norms. Using the selection of appropriate thermal storage electric boiler system, i.e., when the low electric power, the heat stored in the heat storage medium; at peak power stage, the heat stored in the heat storage medium released for users. It features electric boiler thermal storage system is different for peak electricity prices, operating cost savings for the user, and by peak load shifting power grid, good for grid security, economic operation. Electric steam boiler with the steam accumulator reservoir may be higher, the higher the heat of the argument, but the high electric steam boiler plus steam accumulator system cost, operation and management require a higher level, and therefore, do not ask for the heating parameters heating, living, air conditioning system, electric steam boiler plus steam accumulator system is rarely used. Electric power distribution chamber should be supplied directly to the boiler, the discharge conveyor can be used, or a metal cable. Determining the load and the number of electric boiler, boiler room should be combined transformer capacity equipped with comprehensive consideration. Many boilers can share a transformer, but not multiple transformers to supply a common boiler. Taipower power single steam boiler should not be greater than 2.4MW. Steam boiler feed water pot outside the general chemical water treatment, water quality should be specified. Installation and construction, installation points, boilers and auxiliary equipment, water treatment equipment should meet the technical requirements of the device manufacturer. Equipment foundation must be the arrival of equipment and after verification and design drawings before construction. The highest point of the pipeline deflation, the lowest point turn on the water. Acceptance pressure test after the pipe installation. Electric boiler room should all be grounded electrical equipment and heat storing devices. Precautions: power supply voltage can not exceed ± 5% of the rated voltage. Choice of fuel kerosene, diesel oil, do not use gasoline and heavy oil; when winter temperatures below 0 degrees, 0 # diesel oil are often solidification phenomena, not to use, it is best to use -10 # diesel or kerosene. You must be ground wire construction requirements:! Strength of electrical wiring must be separated, such as walking level sensors, pressure sensors and other electrical control of strong and weak lines output lines of the controller separately. When the installation site, should not wear in the same PVC pipe as arranged in parallel should be held at least 200mm intervals. Ban placed around the boiler gasoline, bananas, water and other inflammable and explosive materials. When using a gas boiler-room electronic leak detection alarm device should be installed to prevent accidents.

Burns Hospital Affiliated Hospital of Shanxi Linfen Linfen Steel is attending a hospital burns burns and other diseases. Hot water boiler is essential hospital equipment heat, hot water output can provide disinfection of medical instruments and ward heating demand. With constantly improving our environmental policy, boiler correspondingly introduced more sophisticated Use. Linfen hospital burns to respond positively to the national environmental policy, decided to introduce an environmentally friendly low nitrogen gas hot water boiler. Taking into account the special circumstances of the hospital, the boiler should also have the use of safe, clean overall characteristics. Based on the above considerations, finalize the Linfen hospital with burns boiler party cooperation fast, fast is provided by one side of a gas condensing pressure hot water boiler (CWNS2.1-95 / 70-Y.Q).

Another technology being incorporated by boiler manufacturers is the gas turbine.When a gas turbine is used, natural gas is fired, and the hot gasses are used to spin a turbine attached to an electrical generator to make electricity.Since there is still available heat in the gas that exhausts from the turbine, it is then sent through a Utility Power HRSG (Heat Recovery Steam Generator).Similar to a watertube boiler, the hot exhaust gasses from the turbine heat water in the tubes of the utility power HRSG and turn it into steam, which is then used to turn a second steam-driven turbine attached to another electrical generator.This technology is called “Combined Cycle Cogeneration”, and is a very efficient use of fuel because the same fuel source is used twice to drive turbines.